/* * SiliconBackplane Chipcommon core hardware definitions. * * The chipcommon core provides chip identification, SB control, * JTAG, 0/1/2 UARTs, clock frequency control, a watchdog interrupt timer, * GPIO interface, extbus, and support for serial and parallel flashes. * * $Id: sbchipc.h 385540 2013-02-15 23:14:50Z $ * * Copyright (C) 1999-2013, Broadcom Corporation * * Unless you and Broadcom execute a separate written software license * agreement governing use of this software, this software is licensed to you * under the terms of the GNU General Public License version 2 (the "GPL"), * available at http://www.broadcom.com/licenses/GPLv2.php, with the * following added to such license: * * As a special exception, the copyright holders of this software give you * permission to link this software with independent modules, and to copy and * distribute the resulting executable under terms of your choice, provided that * you also meet, for each linked independent module, the terms and conditions of * the license of that module. An independent module is a module which is not * derived from this software. The special exception does not apply to any * modifications of the software. * * Notwithstanding the above, under no circumstances may you combine this * software in any way with any other Broadcom software provided under a license * other than the GPL, without Broadcom's express prior written consent. */ #ifndef _SBCHIPC_H #define _SBCHIPC_H #ifndef _LANGUAGE_ASSEMBLY /* cpp contortions to concatenate w/arg prescan */ #ifndef PAD #define _PADLINE(line) pad ## line #define _XSTR(line) _PADLINE(line) #define PAD _XSTR(__LINE__) #endif /* PAD */ typedef struct eci_prerev35 { uint32 eci_output; uint32 eci_control; uint32 eci_inputlo; uint32 eci_inputmi; uint32 eci_inputhi; uint32 eci_inputintpolaritylo; uint32 eci_inputintpolaritymi; uint32 eci_inputintpolarityhi; uint32 eci_intmasklo; uint32 eci_intmaskmi; uint32 eci_intmaskhi; uint32 eci_eventlo; uint32 eci_eventmi; uint32 eci_eventhi; uint32 eci_eventmasklo; uint32 eci_eventmaskmi; uint32 eci_eventmaskhi; uint32 PAD[3]; } eci_prerev35_t; typedef struct eci_rev35 { uint32 eci_outputlo; uint32 eci_outputhi; uint32 eci_controllo; uint32 eci_controlhi; uint32 eci_inputlo; uint32 eci_inputhi; uint32 eci_inputintpolaritylo; uint32 eci_inputintpolarityhi; uint32 eci_intmasklo; uint32 eci_intmaskhi; uint32 eci_eventlo; uint32 eci_eventhi; uint32 eci_eventmasklo; uint32 eci_eventmaskhi; uint32 eci_auxtx; uint32 eci_auxrx; uint32 eci_datatag; uint32 eci_uartescvalue; uint32 eci_autobaudctr; uint32 eci_uartfifolevel; } eci_rev35_t; typedef struct flash_config { uint32 PAD[19]; /* Flash struct configuration registers (0x18c) for BCM4706 (corerev = 31) */ uint32 flashstrconfig; } flash_config_t; typedef volatile struct { uint32 chipid; /* 0x0 */ uint32 capabilities; uint32 corecontrol; /* corerev >= 1 */ uint32 bist; /* OTP */ uint32 otpstatus; /* 0x10, corerev >= 10 */ uint32 otpcontrol; uint32 otpprog; uint32 otplayout; /* corerev >= 23 */ /* Interrupt control */ uint32 intstatus; /* 0x20 */ uint32 intmask; /* Chip specific regs */ uint32 chipcontrol; /* 0x28, rev >= 11 */ uint32 chipstatus; /* 0x2c, rev >= 11 */ /* Jtag Master */ uint32 jtagcmd; /* 0x30, rev >= 10 */ uint32 jtagir; uint32 jtagdr; uint32 jtagctrl; /* serial flash interface registers */ uint32 flashcontrol; /* 0x40 */ uint32 flashaddress; uint32 flashdata; uint32 otplayoutextension; /* rev >= 35 */ /* Silicon backplane configuration broadcast control */ uint32 broadcastaddress; /* 0x50 */ uint32 broadcastdata; /* gpio - cleared only by power-on-reset */ uint32 gpiopullup; /* 0x58, corerev >= 20 */ uint32 gpiopulldown; /* 0x5c, corerev >= 20 */ uint32 gpioin; /* 0x60 */ uint32 gpioout; /* 0x64 */ uint32 gpioouten; /* 0x68 */ uint32 gpiocontrol; /* 0x6C */ uint32 gpiointpolarity; /* 0x70 */ uint32 gpiointmask; /* 0x74 */ /* GPIO events corerev >= 11 */ uint32 gpioevent; uint32 gpioeventintmask; /* Watchdog timer */ uint32 watchdog; /* 0x80 */ /* GPIO events corerev >= 11 */ uint32 gpioeventintpolarity; /* GPIO based LED powersave registers corerev >= 16 */ uint32 gpiotimerval; /* 0x88 */ uint32 gpiotimeroutmask; /* clock control */ uint32 clockcontrol_n; /* 0x90 */ uint32 clockcontrol_sb; /* aka m0 */ uint32 clockcontrol_pci; /* aka m1 */ uint32 clockcontrol_m2; /* mii/uart/mipsref */ uint32 clockcontrol_m3; /* cpu */ uint32 clkdiv; /* corerev >= 3 */ uint32 gpiodebugsel; /* corerev >= 28 */ uint32 capabilities_ext; /* 0xac */ /* pll delay registers (corerev >= 4) */ uint32 pll_on_delay; /* 0xb0 */ uint32 fref_sel_delay; uint32 slow_clk_ctl; /* 5 < corerev < 10 */ uint32 PAD; /* Instaclock registers (corerev >= 10) */ uint32 system_clk_ctl; /* 0xc0 */ uint32 clkstatestretch; uint32 PAD[2]; /* Indirect backplane access (corerev >= 22) */ uint32 bp_addrlow; /* 0xd0 */ uint32 bp_addrhigh; uint32 bp_data; uint32 PAD; uint32 bp_indaccess; /* SPI registers, corerev >= 37 */ uint32 gsioctrl; uint32 gsioaddress; uint32 gsiodata; /* More clock dividers (corerev >= 32) */ uint32 clkdiv2; /* FAB ID (corerev >= 40) */ uint32 otpcontrol1; uint32 fabid; /* 0xf8 */ /* In AI chips, pointer to erom */ uint32 eromptr; /* 0xfc */ /* ExtBus control registers (corerev >= 3) */ uint32 pcmcia_config; /* 0x100 */ uint32 pcmcia_memwait; uint32 pcmcia_attrwait; uint32 pcmcia_iowait; uint32 ide_config; uint32 ide_memwait; uint32 ide_attrwait; uint32 ide_iowait; uint32 prog_config; uint32 prog_waitcount; uint32 flash_config; uint32 flash_waitcount; uint32 SECI_config; /* 0x130 SECI configuration */ uint32 SECI_status; uint32 SECI_statusmask; uint32 SECI_rxnibchanged; uint32 PAD[20]; /* SROM interface (corerev >= 32) */ uint32 sromcontrol; /* 0x190 */ uint32 sromaddress; uint32 sromdata; uint32 PAD[1]; /* 0x19C */ /* NAND flash registers for BCM4706 (corerev = 31) */ uint32 nflashctrl; /* 0x1a0 */ uint32 nflashconf; uint32 nflashcoladdr; uint32 nflashrowaddr; uint32 nflashdata; uint32 nflashwaitcnt0; /* 0x1b4 */ uint32 PAD[2]; uint32 seci_uart_data; /* 0x1C0 */ uint32 seci_uart_bauddiv; uint32 seci_uart_fcr; uint32 seci_uart_lcr; uint32 seci_uart_mcr; uint32 seci_uart_lsr; uint32 seci_uart_msr; uint32 seci_uart_baudadj; /* Clock control and hardware workarounds (corerev >= 20) */ uint32 clk_ctl_st; /* 0x1e0 */ uint32 hw_war; uint32 PAD[70]; /* UARTs */ uint8 uart0data; /* 0x300 */ uint8 uart0imr; uint8 uart0fcr; uint8 uart0lcr; uint8 uart0mcr; uint8 uart0lsr; uint8 uart0msr; uint8 uart0scratch; uint8 PAD[248]; /* corerev >= 1 */ uint8 uart1data; /* 0x400 */ uint8 uart1imr; uint8 uart1fcr; uint8 uart1lcr; uint8 uart1mcr; uint8 uart1lsr; uint8 uart1msr; uint8 uart1scratch; uint32 PAD[126]; /* PMU registers (corerev >= 20) */ /* Note: all timers driven by ILP clock are updated asynchronously to HT/ALP. * The CPU must read them twice, compare, and retry if different. */ uint32 pmucontrol; /* 0x600 */ uint32 pmucapabilities; uint32 pmustatus; uint32 res_state; uint32 res_pending; uint32 pmutimer; uint32 min_res_mask; uint32 max_res_mask; uint32 res_table_sel; uint32 res_dep_mask; uint32 res_updn_timer; uint32 res_timer; uint32 clkstretch; uint32 pmuwatchdog; uint32 gpiosel; /* 0x638, rev >= 1 */ uint32 gpioenable; /* 0x63c, rev >= 1 */ uint32 res_req_timer_sel; uint32 res_req_timer; uint32 res_req_mask; uint32 PAD; uint32 chipcontrol_addr; /* 0x650 */ uint32 chipcontrol_data; /* 0x654 */ uint32 regcontrol_addr; uint32 regcontrol_data; uint32 pllcontrol_addr; uint32 pllcontrol_data; uint32 pmustrapopt; /* 0x668, corerev >= 28 */ uint32 pmu_xtalfreq; /* 0x66C, pmurev >= 10 */ uint32 retention_ctl; /* 0x670 */ uint32 PAD[3]; uint32 retention_grpidx; /* 0x680 */ uint32 retention_grpctl; /* 0x684 */ uint32 PAD[94]; uint16 sromotp[512]; /* 0x800 */ #ifdef NFLASH_SUPPORT /* Nand flash MLC controller registers (corerev >= 38) */ uint32 nand_revision; /* 0xC00 */ uint32 nand_cmd_start; uint32 nand_cmd_addr_x; uint32 nand_cmd_addr; uint32 nand_cmd_end_addr; uint32 nand_cs_nand_select; uint32 nand_cs_nand_xor; uint32 PAD; uint32 nand_spare_rd0; uint32 nand_spare_rd4; uint32 nand_spare_rd8; uint32 nand_spare_rd12; uint32 nand_spare_wr0; uint32 nand_spare_wr4; uint32 nand_spare_wr8; uint32 nand_spare_wr12; uint32 nand_acc_control; uint32 PAD; uint32 nand_config; uint32 PAD; uint32 nand_timing_1; uint32 nand_timing_2; uint32 nand_semaphore; uint32 PAD; uint32 nand_devid; uint32 nand_devid_x; uint32 nand_block_lock_status; uint32 nand_intfc_status; uint32 nand_ecc_corr_addr_x; uint32 nand_ecc_corr_addr; uint32 nand_ecc_unc_addr_x; uint32 nand_ecc_unc_addr; uint32 nand_read_error_count; uint32 nand_corr_stat_threshold; uint32 PAD[2]; uint32 nand_read_addr_x; uint32 nand_read_addr; uint32 nand_page_program_addr_x; uint32 nand_page_program_addr; uint32 nand_copy_back_addr_x; uint32 nand_copy_back_addr; uint32 nand_block_erase_addr_x; uint32 nand_block_erase_addr; uint32 nand_inv_read_addr_x; uint32 nand_inv_read_addr; uint32 PAD[2]; uint32 nand_blk_wr_protect; uint32 PAD[3]; uint32 nand_acc_control_cs1; uint32 nand_config_cs1; uint32 nand_timing_1_cs1; uint32 nand_timing_2_cs1; uint32 PAD[20]; uint32 nand_spare_rd16; uint32 nand_spare_rd20; uint32 nand_spare_rd24; uint32 nand_spare_rd28; uint32 nand_cache_addr; uint32 nand_cache_data; uint32 nand_ctrl_config; uint32 nand_ctrl_status; #endif /* NFLASH_SUPPORT */ uint32 gci_corecaps0; /* GCI starting at 0xC00 */ uint32 gci_corecaps1; uint32 gci_corecaps2; uint32 gci_corectrl; uint32 gci_corestat; /* 0xC10 */ uint32 gci_intstat; /* 0xC14 */ uint32 gci_intmask; /* 0xC18 */ uint32 gci_wakemask; /* 0xC1C */ uint32 gci_levelintstat; /* 0xC20 */ uint32 gci_eventintstat; /* 0xC24 */ uint32 PAD[6]; uint32 gci_indirect_addr; /* 0xC40 */ uint32 gci_gpioctl; /* 0xC44 */ uint32 PAD; uint32 gci_gpiomask; /* 0xC4C */ uint32 PAD; uint32 gci_miscctl; /* 0xC54 */ uint32 PAD[2]; uint32 gci_input[32]; /* C60 */ uint32 gci_event[32]; /* CE0 */ uint32 gci_output[4]; /* D60 */ uint32 gci_control_0; /* 0xD70 */ uint32 gci_control_1; /* 0xD74 */ uint32 gci_level_polreg; /* 0xD78 */ uint32 gci_levelintmask; /* 0xD7C */ uint32 gci_eventintmask; /* 0xD80 */ uint32 PAD[3]; uint32 gci_inbandlevelintmask; /* 0xD90 */ uint32 gci_inbandeventintmask; /* 0xD94 */ uint32 PAD[2]; uint32 gci_seciauxtx; /* 0xDA0 */ uint32 gci_seciauxrx; /* 0xDA4 */ uint32 gci_secitx_datatag; /* 0xDA8 */ uint32 gci_secirx_datatag; /* 0xDAC */ uint32 gci_secitx_datamask; /* 0xDB0 */ uint32 gci_seciusef0tx_reg; /* 0xDB4 */ uint32 gci_secif0tx_offset; /* 0xDB8 */ uint32 gci_secif0rx_offset; /* 0xDBC */ uint32 gci_secif1tx_offset; /* 0xDC0 */ uint32 PAD[3]; uint32 gci_uartescval; /* DD0 */ uint32 PAD[3]; uint32 gci_secibauddiv; /* DE0 */ uint32 gci_secifcr; /* DE4 */ uint32 gci_secilcr; /* DE8 */ uint32 gci_secimcr; /* DEC */ uint32 PAD[2]; uint32 gci_baudadj; /* DF8 */ uint32 PAD; uint32 gci_chipctrl; /* 0xE00 */ uint32 gci_chipsts; /* 0xE04 */ } chipcregs_t; #endif /* _LANGUAGE_ASSEMBLY */ #define CC_CHIPID 0 #define CC_CAPABILITIES 4 #define CC_CHIPST 0x2c #define CC_EROMPTR 0xfc #define CC_OTPST 0x10 #define CC_JTAGCMD 0x30 #define CC_JTAGIR 0x34 #define CC_JTAGDR 0x38 #define CC_JTAGCTRL 0x3c #define CC_GPIOPU 0x58 #define CC_GPIOPD 0x5c #define CC_GPIOIN 0x60 #define CC_GPIOOUT 0x64 #define CC_GPIOOUTEN 0x68 #define CC_GPIOCTRL 0x6c #define CC_GPIOPOL 0x70 #define CC_GPIOINTM 0x74 #define CC_WATCHDOG 0x80 #define CC_CLKC_N 0x90 #define CC_CLKC_M0 0x94 #define CC_CLKC_M1 0x98 #define CC_CLKC_M2 0x9c #define CC_CLKC_M3 0xa0 #define CC_CLKDIV 0xa4 #define CC_SYS_CLK_CTL 0xc0 #define CC_CLK_CTL_ST SI_CLK_CTL_ST #define PMU_CTL 0x600 #define PMU_CAP 0x604 #define PMU_ST 0x608 #define PMU_RES_STATE 0x60c #define PMU_TIMER 0x614 #define PMU_MIN_RES_MASK 0x618 #define PMU_MAX_RES_MASK 0x61c #define CC_CHIPCTL_ADDR 0x650 #define CC_CHIPCTL_DATA 0x654 #define PMU_REG_CONTROL_ADDR 0x658 #define PMU_REG_CONTROL_DATA 0x65C #define PMU_PLL_CONTROL_ADDR 0x660 #define PMU_PLL_CONTROL_DATA 0x664 #define CC_SROM_OTP 0x800 /* SROM/OTP address space */ #define CC_GCI_INDIRECT_ADDR_REG 0xC40 #define CC_GCI_CHIP_CTRL_REG 0xE00 #define CC_GCI_CC_OFFSET_2 2 #define CC_GCI_CC_OFFSET_5 5 #ifdef NFLASH_SUPPORT /* NAND flash support */ #define CC_NAND_REVISION 0xC00 #define CC_NAND_CMD_START 0xC04 #define CC_NAND_CMD_ADDR 0xC0C #define CC_NAND_SPARE_RD_0 0xC20 #define CC_NAND_SPARE_RD_4 0xC24 #define CC_NAND_SPARE_RD_8 0xC28 #define CC_NAND_SPARE_RD_C 0xC2C #define CC_NAND_CONFIG 0xC48 #define CC_NAND_DEVID 0xC60 #define CC_NAND_DEVID_EXT 0xC64 #define CC_NAND_INTFC_STATUS 0xC6C #endif /* NFLASH_SUPPORT */ /* chipid */ #define CID_ID_MASK 0x0000ffff /* Chip Id mask */ #define CID_REV_MASK 0x000f0000 /* Chip Revision mask */ #define CID_REV_SHIFT 16 /* Chip Revision shift */ #define CID_PKG_MASK 0x00f00000 /* Package Option mask */ #define CID_PKG_SHIFT 20 /* Package Option shift */ #define CID_CC_MASK 0x0f000000 /* CoreCount (corerev >= 4) */ #define CID_CC_SHIFT 24 #define CID_TYPE_MASK 0xf0000000 /* Chip Type */ #define CID_TYPE_SHIFT 28 /* capabilities */ #define CC_CAP_UARTS_MASK 0x00000003 /* Number of UARTs */ #define CC_CAP_MIPSEB 0x00000004 /* MIPS is in big-endian mode */ #define CC_CAP_UCLKSEL 0x00000018 /* UARTs clock select */ #define CC_CAP_UINTCLK 0x00000008 /* UARTs are driven by internal divided clock */ #define CC_CAP_UARTGPIO 0x00000020 /* UARTs own GPIOs 15:12 */ #define CC_CAP_EXTBUS_MASK 0x000000c0 /* External bus mask */ #define CC_CAP_EXTBUS_NONE 0x00000000 /* No ExtBus present */ #define CC_CAP_EXTBUS_FULL 0x00000040 /* ExtBus: PCMCIA, IDE & Prog */ #define CC_CAP_EXTBUS_PROG 0x00000080 /* ExtBus: ProgIf only */ #define CC_CAP_FLASH_MASK 0x00000700 /* Type of flash */ #define CC_CAP_PLL_MASK 0x00038000 /* Type of PLL */ #define CC_CAP_PWR_CTL 0x00040000 /* Power control */ #define CC_CAP_OTPSIZE 0x00380000 /* OTP Size (0 = none) */ #define CC_CAP_OTPSIZE_SHIFT 19 /* OTP Size shift */ #define CC_CAP_OTPSIZE_BASE 5 /* OTP Size base */ #define CC_CAP_JTAGP 0x00400000 /* JTAG Master Present */ #define CC_CAP_ROM 0x00800000 /* Internal boot rom active */ #define CC_CAP_BKPLN64 0x08000000 /* 64-bit backplane */ #define CC_CAP_PMU 0x10000000 /* PMU Present, rev >= 20 */ #define CC_CAP_ECI 0x20000000 /* ECI Present, rev >= 21 */ #define CC_CAP_SROM 0x40000000 /* Srom Present, rev >= 32 */ #define CC_CAP_NFLASH 0x80000000 /* Nand flash present, rev >= 35 */ #define CC_CAP2_SECI 0x00000001 /* SECI Present, rev >= 36 */ #define CC_CAP2_GSIO 0x00000002 /* GSIO (spi/i2c) present, rev >= 37 */ /* capabilities extension */ #define CC_CAP_EXT_SECI_PRESENT 0x00000001 /* SECI present */ #define CC_CAP_EXT_GCI_PRESENT 0x00000004 /* GCI present */ /* WL Channel Info to BT via GCI - bits 40 - 47 */ #define GCI_WL_CHN_INFO_MASK (0xFF00) /* PLL type */ #define PLL_NONE 0x00000000 #define PLL_TYPE1 0x00010000 /* 48MHz base, 3 dividers */ #define PLL_TYPE2 0x00020000 /* 48MHz, 4 dividers */ #define PLL_TYPE3 0x00030000 /* 25MHz, 2 dividers */ #define PLL_TYPE4 0x00008000 /* 48MHz, 4 dividers */ #define PLL_TYPE5 0x00018000 /* 25MHz, 4 dividers */ #define PLL_TYPE6 0x00028000 /* 100/200 or 120/240 only */ #define PLL_TYPE7 0x00038000 /* 25MHz, 4 dividers */ /* ILP clock */ #define ILP_CLOCK 32000 /* ALP clock on pre-PMU chips */ #define ALP_CLOCK 20000000 #ifdef CFG_SIM #define NS_ALP_CLOCK 84922 #define NS_SLOW_ALP_CLOCK 84922 #define NS_CPU_CLOCK 534500 #define NS_SLOW_CPU_CLOCK 534500 #define NS_SI_CLOCK 271750 #define NS_SLOW_SI_CLOCK 271750 #define NS_FAST_MEM_CLOCK 271750 #define NS_MEM_CLOCK 271750 #define NS_SLOW_MEM_CLOCK 271750 #else #define NS_ALP_CLOCK 125000000 #define NS_SLOW_ALP_CLOCK 100000000 #define NS_CPU_CLOCK 1000000000 #define NS_SLOW_CPU_CLOCK 800000000 #define NS_SI_CLOCK 250000000 #define NS_SLOW_SI_CLOCK 200000000 #define NS_FAST_MEM_CLOCK 800000000 #define NS_MEM_CLOCK 533000000 #define NS_SLOW_MEM_CLOCK 400000000 #endif /* CFG_SIM */ /* HT clock */ #define HT_CLOCK 80000000 /* corecontrol */ #define CC_UARTCLKO 0x00000001 /* Drive UART with internal clock */ #define CC_SE 0x00000002 /* sync clk out enable (corerev >= 3) */ #define CC_ASYNCGPIO 0x00000004 /* 1=generate GPIO interrupt without backplane clock */ #define CC_UARTCLKEN 0x00000008 /* enable UART Clock (corerev > = 21 */ /* 4321 chipcontrol */ #define CHIPCTRL_4321A0_DEFAULT 0x3a4 #define CHIPCTRL_4321A1_DEFAULT 0x0a4 #define CHIPCTRL_4321_PLL_DOWN 0x800000 /* serdes PLL down override */ /* Fields in the otpstatus register in rev >= 21 */ #define OTPS_OL_MASK 0x000000ff #define OTPS_OL_MFG 0x00000001 /* manuf row is locked */ #define OTPS_OL_OR1 0x00000002 /* otp redundancy row 1 is locked */ #define OTPS_OL_OR2 0x00000004 /* otp redundancy row 2 is locked */ #define OTPS_OL_GU 0x00000008 /* general use region is locked */ #define OTPS_GUP_MASK 0x00000f00 #define OTPS_GUP_SHIFT 8 #define OTPS_GUP_HW 0x00000100 /* h/w subregion is programmed */ #define OTPS_GUP_SW 0x00000200 /* s/w subregion is programmed */ #define OTPS_GUP_CI 0x00000400 /* chipid/pkgopt subregion is programmed */ #define OTPS_GUP_FUSE 0x00000800 /* fuse subregion is programmed */ #define OTPS_READY 0x00001000 #define OTPS_RV(x) (1 << (16 + (x))) /* redundancy entry valid */ #define OTPS_RV_MASK 0x0fff0000 #define OTPS_PROGOK 0x40000000 /* Fields in the otpcontrol register in rev >= 21 */ #define OTPC_PROGSEL 0x00000001 #define OTPC_PCOUNT_MASK 0x0000000e #define OTPC_PCOUNT_SHIFT 1 #define OTPC_VSEL_MASK 0x000000f0 #define OTPC_VSEL_SHIFT 4 #define OTPC_TMM_MASK 0x00000700 #define OTPC_TMM_SHIFT 8 #define OTPC_ODM 0x00000800 #define OTPC_PROGEN 0x80000000 /* Fields in the 40nm otpcontrol register in rev >= 40 */ #define OTPC_40NM_PROGSEL_SHIFT 0 #define OTPC_40NM_PCOUNT_SHIFT 1 #define OTPC_40NM_PCOUNT_WR 0xA #define OTPC_40NM_PCOUNT_V1X 0xB #define OTPC_40NM_REGCSEL_SHIFT 5 #define OTPC_40NM_REGCSEL_DEF 0x4 #define OTPC_40NM_PROGIN_SHIFT 8 #define OTPC_40NM_R2X_SHIFT 10 #define OTPC_40NM_ODM_SHIFT 11 #define OTPC_40NM_DF_SHIFT 15 #define OTPC_40NM_VSEL_SHIFT 16 #define OTPC_40NM_VSEL_WR 0xA #define OTPC_40NM_VSEL_V1X 0xA #define OTPC_40NM_VSEL_R1X 0x5 #define OTPC_40NM_COFAIL_SHIFT 30 #define OTPC1_CPCSEL_SHIFT 0 #define OTPC1_CPCSEL_DEF 6 #define OTPC1_TM_SHIFT 8 #define OTPC1_TM_WR 0x84 #define OTPC1_TM_V1X 0x84 #define OTPC1_TM_R1X 0x4 /* Fields in otpprog in rev >= 21 and HND OTP */ #define OTPP_COL_MASK 0x000000ff #define OTPP_COL_SHIFT 0 #define OTPP_ROW_MASK 0x0000ff00 #define OTPP_ROW_SHIFT 8 #define OTPP_OC_MASK 0x0f000000 #define OTPP_OC_SHIFT 24 #define OTPP_READERR 0x10000000 #define OTPP_VALUE_MASK 0x20000000 #define OTPP_VALUE_SHIFT 29 #define OTPP_START_BUSY 0x80000000 #define OTPP_READ 0x40000000 /* HND OTP */ /* Fields in otplayout register */ #define OTPL_HWRGN_OFF_MASK 0x00000FFF #define OTPL_HWRGN_OFF_SHIFT 0 #define OTPL_WRAP_REVID_MASK 0x00F80000 #define OTPL_WRAP_REVID_SHIFT 19 #define OTPL_WRAP_TYPE_MASK 0x00070000 #define OTPL_WRAP_TYPE_SHIFT 16 #define OTPL_WRAP_TYPE_65NM 0 #define OTPL_WRAP_TYPE_40NM 1 /* otplayout reg corerev >= 36 */ #define OTP_CISFORMAT_NEW 0x80000000 /* Opcodes for OTPP_OC field */ #define OTPPOC_READ 0 #define OTPPOC_BIT_PROG 1 #define OTPPOC_VERIFY 3 #define OTPPOC_INIT 4 #define OTPPOC_SET 5 #define OTPPOC_RESET 6 #define OTPPOC_OCST 7 #define OTPPOC_ROW_LOCK 8 #define OTPPOC_PRESCN_TEST 9 /* Opcodes for OTPP_OC field (40NM) */ #define OTPPOC_READ_40NM 0 #define OTPPOC_PROG_ENABLE_40NM 1 #define OTPPOC_PROG_DISABLE_40NM 2 #define OTPPOC_VERIFY_40NM 3 #define OTPPOC_WORD_VERIFY_1_40NM 4 #define OTPPOC_ROW_LOCK_40NM 5 #define OTPPOC_STBY_40NM 6 #define OTPPOC_WAKEUP_40NM 7 #define OTPPOC_WORD_VERIFY_0_40NM 8 #define OTPPOC_PRESCN_TEST_40NM 9 #define OTPPOC_BIT_PROG_40NM 10 #define OTPPOC_WORDPROG_40NM 11 #define OTPPOC_BURNIN_40NM 12 #define OTPPOC_AUTORELOAD_40NM 13 #define OTPPOC_OVST_READ_40NM 14 #define OTPPOC_OVST_PROG_40NM 15 /* Fields in otplayoutextension */ #define OTPLAYOUTEXT_FUSE_MASK 0x3FF /* Jtagm characteristics that appeared at a given corerev */ #define JTAGM_CREV_OLD 10 /* Old command set, 16bit max IR */ #define JTAGM_CREV_IRP 22 /* Able to do pause-ir */ #define JTAGM_CREV_RTI 28 /* Able to do return-to-idle */ /* jtagcmd */ #define JCMD_START 0x80000000 #define JCMD_BUSY 0x80000000 #define JCMD_STATE_MASK 0x60000000 #define JCMD_STATE_TLR 0x00000000 /* Test-logic-reset */ #define JCMD_STATE_PIR 0x20000000 /* Pause IR */ #define JCMD_STATE_PDR 0x40000000 /* Pause DR */ #define JCMD_STATE_RTI 0x60000000 /* Run-test-idle */ #define JCMD0_ACC_MASK 0x0000f000 #define JCMD0_ACC_IRDR 0x00000000 #define JCMD0_ACC_DR 0x00001000 #define JCMD0_ACC_IR 0x00002000 #define JCMD0_ACC_RESET 0x00003000 #define JCMD0_ACC_IRPDR 0x00004000 #define JCMD0_ACC_PDR 0x00005000 #define JCMD0_IRW_MASK 0x00000f00 #define JCMD_ACC_MASK 0x000f0000 /* Changes for corerev 11 */ #define JCMD_ACC_IRDR 0x00000000 #define JCMD_ACC_DR 0x00010000 #define JCMD_ACC_IR 0x00020000 #define JCMD_ACC_RESET 0x00030000 #define JCMD_ACC_IRPDR 0x00040000 #define JCMD_ACC_PDR 0x00050000 #define JCMD_ACC_PIR 0x00060000 #define JCMD_ACC_IRDR_I 0x00070000 /* rev 28: return to run-test-idle */ #define JCMD_ACC_DR_I 0x00080000 /* rev 28: return to run-test-idle */ #define JCMD_IRW_MASK 0x00001f00 #define JCMD_IRW_SHIFT 8 #define JCMD_DRW_MASK 0x0000003f /* jtagctrl */ #define JCTRL_FORCE_CLK 4 /* Force clock */ #define JCTRL_EXT_EN 2 /* Enable external targets */ #define JCTRL_EN 1 /* Enable Jtag master */ /* Fields in clkdiv */ #define CLKD_SFLASH 0x0f000000 #define CLKD_SFLASH_SHIFT 24 #define CLKD_OTP 0x000f0000 #define CLKD_OTP_SHIFT 16 #define CLKD_JTAG 0x00000f00 #define CLKD_JTAG_SHIFT 8 #define CLKD_UART 0x000000ff #define CLKD2_SROM 0x00000003 /* intstatus/intmask */ #define CI_GPIO 0x00000001 /* gpio intr */ #define CI_EI 0x00000002 /* extif intr (corerev >= 3) */ #define CI_TEMP 0x00000004 /* temp. ctrl intr (corerev >= 15) */ #define CI_SIRQ 0x00000008 /* serial IRQ intr (corerev >= 15) */ #define CI_ECI 0x00000010 /* eci intr (corerev >= 21) */ #define CI_PMU 0x00000020 /* pmu intr (corerev >= 21) */ #define CI_UART 0x00000040 /* uart intr (corerev >= 21) */ #define CI_WDRESET 0x80000000 /* watchdog reset occurred */ /* slow_clk_ctl */ #define SCC_SS_MASK 0x00000007 /* slow clock source mask */ #define SCC_SS_LPO 0x00000000 /* source of slow clock is LPO */ #define SCC_SS_XTAL 0x00000001 /* source of slow clock is crystal */ #define SCC_SS_PCI 0x00000002 /* source of slow clock is PCI */ #define SCC_LF 0x00000200 /* LPOFreqSel, 1: 160Khz, 0: 32KHz */ #define SCC_LP 0x00000400 /* LPOPowerDown, 1: LPO is disabled, * 0: LPO is enabled */ #define SCC_FS 0x00000800 /* ForceSlowClk, 1: sb/cores running on slow clock, * 0: power logic control */ #define SCC_IP 0x00001000 /* IgnorePllOffReq, 1/0: power logic ignores/honors * PLL clock disable requests from core */ #define SCC_XC 0x00002000 /* XtalControlEn, 1/0: power logic does/doesn't * disable crystal when appropriate */ #define SCC_XP 0x00004000 /* XtalPU (RO), 1/0: crystal running/disabled */ #define SCC_CD_MASK 0xffff0000 /* ClockDivider (SlowClk = 1/(4+divisor)) */ #define SCC_CD_SHIFT 16 /* system_clk_ctl */ #define SYCC_IE 0x00000001 /* ILPen: Enable Idle Low Power */ #define SYCC_AE 0x00000002 /* ALPen: Enable Active Low Power */ #define SYCC_FP 0x00000004 /* ForcePLLOn */ #define SYCC_AR 0x00000008 /* Force ALP (or HT if ALPen is not set */ #define SYCC_HR 0x00000010 /* Force HT */ #define SYCC_CD_MASK 0xffff0000 /* ClkDiv (ILP = 1/(4 * (divisor + 1)) */ #define SYCC_CD_SHIFT 16 /* Indirect backplane access */ #define BPIA_BYTEEN 0x0000000f #define BPIA_SZ1 0x00000001 #define BPIA_SZ2 0x00000003 #define BPIA_SZ4 0x00000007 #define BPIA_SZ8 0x0000000f #define BPIA_WRITE 0x00000100 #define BPIA_START 0x00000200 #define BPIA_BUSY 0x00000200 #define BPIA_ERROR 0x00000400 /* pcmcia/prog/flash_config */ #define CF_EN 0x00000001 /* enable */ #define CF_EM_MASK 0x0000000e /* mode */ #define CF_EM_SHIFT 1 #define CF_EM_FLASH 0 /* flash/asynchronous mode */ #define CF_EM_SYNC 2 /* synchronous mode */ #define CF_EM_PCMCIA 4 /* pcmcia mode */ #define CF_DS 0x00000010 /* destsize: 0=8bit, 1=16bit */ #define CF_BS 0x00000020 /* byteswap */ #define CF_CD_MASK 0x000000c0 /* clock divider */ #define CF_CD_SHIFT 6 #define CF_CD_DIV2 0x00000000 /* backplane/2 */ #define CF_CD_DIV3 0x00000040 /* backplane/3 */ #define CF_CD_DIV4 0x00000080 /* backplane/4 */ #define CF_CE 0x00000100 /* clock enable */ #define CF_SB 0x00000200 /* size/bytestrobe (synch only) */ /* pcmcia_memwait */ #define PM_W0_MASK 0x0000003f /* waitcount0 */ #define PM_W1_MASK 0x00001f00 /* waitcount1 */ #define PM_W1_SHIFT 8 #define PM_W2_MASK 0x001f0000 /* waitcount2 */ #define PM_W2_SHIFT 16 #define PM_W3_MASK 0x1f000000 /* waitcount3 */ #define PM_W3_SHIFT 24 /* pcmcia_attrwait */ #define PA_W0_MASK 0x0000003f /* waitcount0 */ #define PA_W1_MASK 0x00001f00 /* waitcount1 */ #define PA_W1_SHIFT 8 #define PA_W2_MASK 0x001f0000 /* waitcount2 */ #define PA_W2_SHIFT 16 #define PA_W3_MASK 0x1f000000 /* waitcount3 */ #define PA_W3_SHIFT 24 /* pcmcia_iowait */ #define PI_W0_MASK 0x0000003f /* waitcount0 */ #define PI_W1_MASK 0x00001f00 /* waitcount1 */ #define PI_W1_SHIFT 8 #define PI_W2_MASK 0x001f0000 /* waitcount2 */ #define PI_W2_SHIFT 16 #define PI_W3_MASK 0x1f000000 /* waitcount3 */ #define PI_W3_SHIFT 24 /* prog_waitcount */ #define PW_W0_MASK 0x0000001f /* waitcount0 */ #define PW_W1_MASK 0x00001f00 /* waitcount1 */ #define PW_W1_SHIFT 8 #define PW_W2_MASK 0x001f0000 /* waitcount2 */ #define PW_W2_SHIFT 16 #define PW_W3_MASK 0x1f000000 /* waitcount3 */ #define PW_W3_SHIFT 24 #define PW_W0 0x0000000c #define PW_W1 0x00000a00 #define PW_W2 0x00020000 #define PW_W3 0x01000000 /* flash_waitcount */ #define FW_W0_MASK 0x0000003f /* waitcount0 */ #define FW_W1_MASK 0x00001f00 /* waitcount1 */ #define FW_W1_SHIFT 8 #define FW_W2_MASK 0x001f0000 /* waitcount2 */ #define FW_W2_SHIFT 16 #define FW_W3_MASK 0x1f000000 /* waitcount3 */ #define FW_W3_SHIFT 24 /* When Srom support present, fields in sromcontrol */ #define SRC_START 0x80000000 #define SRC_BUSY 0x80000000 #define SRC_OPCODE 0x60000000 #define SRC_OP_READ 0x00000000 #define SRC_OP_WRITE 0x20000000 #define SRC_OP_WRDIS 0x40000000 #define SRC_OP_WREN 0x60000000 #define SRC_OTPSEL 0x00000010 #define SRC_LOCK 0x00000008 #define SRC_SIZE_MASK 0x00000006 #define SRC_SIZE_1K 0x00000000 #define SRC_SIZE_4K 0x00000002 #define SRC_SIZE_16K 0x00000004 #define SRC_SIZE_SHIFT 1 #define SRC_PRESENT 0x00000001 /* Fields in pmucontrol */ #define PCTL_ILP_DIV_MASK 0xffff0000 #define PCTL_ILP_DIV_SHIFT 16 #define PCTL_PLL_PLLCTL_UPD 0x00000400 /* rev 2 */ #define PCTL_NOILP_ON_WAIT 0x00000200 /* rev 1 */ #define PCTL_HT_REQ_EN 0x00000100 #define PCTL_ALP_REQ_EN 0x00000080 #define PCTL_XTALFREQ_MASK 0x0000007c #define PCTL_XTALFREQ_SHIFT 2 #define PCTL_ILP_DIV_EN 0x00000002 #define PCTL_LPO_SEL 0x00000001 /* Retention Control */ #define PMU_RCTL_CLK_DIV_SHIFT 0 #define PMU_RCTL_CHAIN_LEN_SHIFT 12 #define PMU_RCTL_MACPHY_DISABLE_SHIFT 26 #define PMU_RCTL_MACPHY_DISABLE_MASK (1 << 26) #define PMU_RCTL_LOGIC_DISABLE_SHIFT 27 #define PMU_RCTL_LOGIC_DISABLE_MASK (1 << 27) #define PMU_RCTL_MEMSLP_LOG_SHIFT 28 #define PMU_RCTL_MEMSLP_LOG_MASK (1 << 28) #define PMU_RCTL_MEMRETSLP_LOG_SHIFT 29 #define PMU_RCTL_MEMRETSLP_LOG_MASK (1 << 29) /* Retention Group Control */ #define PMU_RCTLGRP_CHAIN_LEN_SHIFT 0 #define PMU_RCTLGRP_RMODE_ENABLE_SHIFT 14 #define PMU_RCTLGRP_RMODE_ENABLE_MASK (1 << 14) #define PMU_RCTLGRP_DFT_ENABLE_SHIFT 15 #define PMU_RCTLGRP_DFT_ENABLE_MASK (1 << 15) #define PMU_RCTLGRP_NSRST_DISABLE_SHIFT 16 #define PMU_RCTLGRP_NSRST_DISABLE_MASK (1 << 16) /* Retention Group Control special for 4334 */ #define PMU4334_RCTLGRP_CHAIN_LEN_GRP0 338 #define PMU4334_RCTLGRP_CHAIN_LEN_GRP1 315 /* Retention Group Control special for 43341 */ #define PMU43341_RCTLGRP_CHAIN_LEN_GRP0 366 #define PMU43341_RCTLGRP_CHAIN_LEN_GRP1 330 /* Fields in clkstretch */ #define CSTRETCH_HT 0xffff0000 #define CSTRETCH_ALP 0x0000ffff /* gpiotimerval */ #define GPIO_ONTIME_SHIFT 16 /* clockcontrol_n */ #define CN_N1_MASK 0x3f /* n1 control */ #define CN_N2_MASK 0x3f00 /* n2 control */ #define CN_N2_SHIFT 8 #define CN_PLLC_MASK 0xf0000 /* pll control */ #define CN_PLLC_SHIFT 16 /* clockcontrol_sb/pci/uart */ #define CC_M1_MASK 0x3f /* m1 control */ #define CC_M2_MASK 0x3f00 /* m2 control */ #define CC_M2_SHIFT 8 #define CC_M3_MASK 0x3f0000 /* m3 control */ #define CC_M3_SHIFT 16 #define CC_MC_MASK 0x1f000000 /* mux control */ #define CC_MC_SHIFT 24 /* N3M Clock control magic field values */ #define CC_F6_2 0x02 /* A factor of 2 in */ #define CC_F6_3 0x03 /* 6-bit fields like */ #define CC_F6_4 0x05 /* N1, M1 or M3 */ #define CC_F6_5 0x09 #define CC_F6_6 0x11 #define CC_F6_7 0x21 #define CC_F5_BIAS 5 /* 5-bit fields get this added */ #define CC_MC_BYPASS 0x08 #define CC_MC_M1 0x04 #define CC_MC_M1M2 0x02 #define CC_MC_M1M2M3 0x01 #define CC_MC_M1M3 0x11 /* Type 2 Clock control magic field values */ #define CC_T2_BIAS 2 /* n1, n2, m1 & m3 bias */ #define CC_T2M2_BIAS 3 /* m2 bias */ #define CC_T2MC_M1BYP 1 #define CC_T2MC_M2BYP 2 #define CC_T2MC_M3BYP 4 /* Type 6 Clock control magic field values */ #define CC_T6_MMASK 1 /* bits of interest in m */ #define CC_T6_M0 120000000 /* sb clock for m = 0 */ #define CC_T6_M1 100000000 /* sb clock for m = 1 */ #define SB2MIPS_T6(sb) (2 * (sb)) /* Common clock base */ #define CC_CLOCK_BASE1 24000000 /* Half the clock freq */ #define CC_CLOCK_BASE2 12500000 /* Alternate crystal on some PLLs */ /* Clock control values for 200MHz in 5350 */ #define CLKC_5350_N 0x0311 #define CLKC_5350_M 0x04020009 /* Flash types in the chipcommon capabilities register */ #define FLASH_NONE 0x000 /* No flash */ #define SFLASH_ST 0x100 /* ST serial flash */ #define SFLASH_AT 0x200 /* Atmel serial flash */ #define NFLASH 0x300 #define PFLASH 0x700 /* Parallel flash */ #define QSPIFLASH_ST 0x800 #define QSPIFLASH_AT 0x900 /* Bits in the ExtBus config registers */ #define CC_CFG_EN 0x0001 /* Enable */ #define CC_CFG_EM_MASK 0x000e /* Extif Mode */ #define CC_CFG_EM_ASYNC 0x0000 /* Async/Parallel flash */ #define CC_CFG_EM_SYNC 0x0002 /* Synchronous */ #define CC_CFG_EM_PCMCIA 0x0004 /* PCMCIA */ #define CC_CFG_EM_IDE 0x0006 /* IDE */ #define CC_CFG_DS 0x0010 /* Data size, 0=8bit, 1=16bit */ #define CC_CFG_CD_MASK 0x00e0 /* Sync: Clock divisor, rev >= 20 */ #define CC_CFG_CE 0x0100 /* Sync: Clock enable, rev >= 20 */ #define CC_CFG_SB 0x0200 /* Sync: Size/Bytestrobe, rev >= 20 */ #define CC_CFG_IS 0x0400 /* Extif Sync Clk Select, rev >= 20 */ /* ExtBus address space */ #define CC_EB_BASE 0x1a000000 /* Chipc ExtBus base address */ #define CC_EB_PCMCIA_MEM 0x1a000000 /* PCMCIA 0 memory base address */ #define CC_EB_PCMCIA_IO 0x1a200000 /* PCMCIA 0 I/O base address */ #define CC_EB_PCMCIA_CFG 0x1a400000 /* PCMCIA 0 config base address */ #define CC_EB_IDE 0x1a800000 /* IDE memory base */ #define CC_EB_PCMCIA1_MEM 0x1a800000 /* PCMCIA 1 memory base address */ #define CC_EB_PCMCIA1_IO 0x1aa00000 /* PCMCIA 1 I/O base address */ #define CC_EB_PCMCIA1_CFG 0x1ac00000 /* PCMCIA 1 config base address */ #define CC_EB_PROGIF 0x1b000000 /* ProgIF Async/Sync base address */ /* Start/busy bit in flashcontrol */ #define SFLASH_OPCODE 0x000000ff #define SFLASH_ACTION 0x00000700 #define SFLASH_CS_ACTIVE 0x00001000 /* Chip Select Active, rev >= 20 */ #define SFLASH_START 0x80000000 #define SFLASH_BUSY SFLASH_START /* flashcontrol action codes */ #define SFLASH_ACT_OPONLY 0x0000 /* Issue opcode only */ #define SFLASH_ACT_OP1D 0x0100 /* opcode + 1 data byte */ #define SFLASH_ACT_OP3A 0x0200 /* opcode + 3 addr bytes */ #define SFLASH_ACT_OP3A1D 0x0300 /* opcode + 3 addr & 1 data bytes */ #define SFLASH_ACT_OP3A4D 0x0400 /* opcode + 3 addr & 4 data bytes */ #define SFLASH_ACT_OP3A4X4D 0x0500 /* opcode + 3 addr, 4 don't care & 4 data bytes */ #define SFLASH_ACT_OP3A1X4D 0x0700 /* opcode + 3 addr, 1 don't care & 4 data bytes */ /* flashcontrol action+opcodes for ST flashes */ #define SFLASH_ST_WREN 0x0006 /* Write Enable */ #define SFLASH_ST_WRDIS 0x0004 /* Write Disable */ #define SFLASH_ST_RDSR 0x0105 /* Read Status Register */ #define SFLASH_ST_WRSR 0x0101 /* Write Status Register */ #define SFLASH_ST_READ 0x0303 /* Read Data Bytes */ #define SFLASH_ST_PP 0x0302 /* Page Program */ #define SFLASH_ST_SE 0x02d8 /* Sector Erase */ #define SFLASH_ST_BE 0x00c7 /* Bulk Erase */ #define SFLASH_ST_DP 0x00b9 /* Deep Power-down */ #define SFLASH_ST_RES 0x03ab /* Read Electronic Signature */ #define SFLASH_ST_CSA 0x1000 /* Keep chip select asserted */ #define SFLASH_ST_SSE 0x0220 /* Sub-sector Erase */ #define SFLASH_MXIC_RDID 0x0390 /* Read Manufacture ID */ #define SFLASH_MXIC_MFID 0xc2 /* MXIC Manufacture ID */ /* Status register bits for ST flashes */ #define SFLASH_ST_WIP 0x01 /* Write In Progress */ #define SFLASH_ST_WEL 0x02 /* Write Enable Latch */ #define SFLASH_ST_BP_MASK 0x1c /* Block Protect */ #define SFLASH_ST_BP_SHIFT 2 #define SFLASH_ST_SRWD 0x80 /* Status Register Write Disable */ /* flashcontrol action+opcodes for Atmel flashes */ #define SFLASH_AT_READ 0x07e8 #define SFLASH_AT_PAGE_READ 0x07d2 #define SFLASH_AT_BUF1_READ #define SFLASH_AT_BUF2_READ #define SFLASH_AT_STATUS 0x01d7 #define SFLASH_AT_BUF1_WRITE 0x0384 #define SFLASH_AT_BUF2_WRITE 0x0387 #define SFLASH_AT_BUF1_ERASE_PROGRAM 0x0283 #define SFLASH_AT_BUF2_ERASE_PROGRAM 0x0286 #define SFLASH_AT_BUF1_PROGRAM 0x0288 #define SFLASH_AT_BUF2_PROGRAM 0x0289 #define SFLASH_AT_PAGE_ERASE 0x0281 #define SFLASH_AT_BLOCK_ERASE 0x0250 #define SFLASH_AT_BUF1_WRITE_ERASE_PROGRAM 0x0382 #define SFLASH_AT_BUF2_WRITE_ERASE_PROGRAM 0x0385 #define SFLASH_AT_BUF1_LOAD 0x0253 #define SFLASH_AT_BUF2_LOAD 0x0255 #define SFLASH_AT_BUF1_COMPARE 0x0260 #define SFLASH_AT_BUF2_COMPARE 0x0261 #define SFLASH_AT_BUF1_REPROGRAM 0x0258 #define SFLASH_AT_BUF2_REPROGRAM 0x0259 /* Status register bits for Atmel flashes */ #define SFLASH_AT_READY 0x80 #define SFLASH_AT_MISMATCH 0x40 #define SFLASH_AT_ID_MASK 0x38 #define SFLASH_AT_ID_SHIFT 3 /* SPI register bits, corerev >= 37 */ #define GSIO_START 0x80000000 #define GSIO_BUSY GSIO_START /* * These are the UART port assignments, expressed as offsets from the base * register. These assignments should hold for any serial port based on * a 8250, 16450, or 16550(A). */ #define UART_RX 0 /* In: Receive buffer (DLAB=0) */ #define UART_TX 0 /* Out: Transmit buffer (DLAB=0) */ #define UART_DLL 0 /* Out: Divisor Latch Low (DLAB=1) */ #define UART_IER 1 /* In/Out: Interrupt Enable Register (DLAB=0) */ #define UART_DLM 1 /* Out: Divisor Latch High (DLAB=1) */ #define UART_IIR 2 /* In: Interrupt Identity Register */ #define UART_FCR 2 /* Out: FIFO Control Register */ #define UART_LCR 3 /* Out: Line Control Register */ #define UART_MCR 4 /* Out: Modem Control Register */ #define UART_LSR 5 /* In: Line Status Register */ #define UART_MSR 6 /* In: Modem Status Register */ #define UART_SCR 7 /* I/O: Scratch Register */ #define UART_LCR_DLAB 0x80 /* Divisor latch access bit */ #define UART_LCR_WLEN8 0x03 /* Word length: 8 bits */ #define UART_MCR_OUT2 0x08 /* MCR GPIO out 2 */ #define UART_MCR_LOOP 0x10 /* Enable loopback test mode */ #define UART_LSR_RX_FIFO 0x80 /* Receive FIFO error */ #define UART_LSR_TDHR 0x40 /* Data-hold-register empty */ #define UART_LSR_THRE 0x20 /* Transmit-hold-register empty */ #define UART_LSR_BREAK 0x10 /* Break interrupt */ #define UART_LSR_FRAMING 0x08 /* Framing error */ #define UART_LSR_PARITY 0x04 /* Parity error */ #define UART_LSR_OVERRUN 0x02 /* Overrun error */ #define UART_LSR_RXRDY 0x01 /* Receiver ready */ #define UART_FCR_FIFO_ENABLE 1 /* FIFO control register bit controlling FIFO enable/disable */ /* Interrupt Identity Register (IIR) bits */ #define UART_IIR_FIFO_MASK 0xc0 /* IIR FIFO disable/enabled mask */ #define UART_IIR_INT_MASK 0xf /* IIR interrupt ID source */ #define UART_IIR_MDM_CHG 0x0 /* Modem status changed */ #define UART_IIR_NOINT 0x1 /* No interrupt pending */ #define UART_IIR_THRE 0x2 /* THR empty */ #define UART_IIR_RCVD_DATA 0x4 /* Received data available */ #define UART_IIR_RCVR_STATUS 0x6 /* Receiver status */ #define UART_IIR_CHAR_TIME 0xc /* Character time */ /* Interrupt Enable Register (IER) bits */ #define UART_IER_EDSSI 8 /* enable modem status interrupt */ #define UART_IER_ELSI 4 /* enable receiver line status interrupt */ #define UART_IER_ETBEI 2 /* enable transmitter holding register empty interrupt */ #define UART_IER_ERBFI 1 /* enable data available interrupt */ /* pmustatus */ #define PST_EXTLPOAVAIL 0x0100 #define PST_WDRESET 0x0080 #define PST_INTPEND 0x0040 #define PST_SBCLKST 0x0030 #define PST_SBCLKST_ILP 0x0010 #define PST_SBCLKST_ALP 0x0020 #define PST_SBCLKST_HT 0x0030 #define PST_ALPAVAIL 0x0008 #define PST_HTAVAIL 0x0004 #define PST_RESINIT 0x0003 /* pmucapabilities */ #define PCAP_REV_MASK 0x000000ff #define PCAP_RC_MASK 0x00001f00 #define PCAP_RC_SHIFT 8 #define PCAP_TC_MASK 0x0001e000 #define PCAP_TC_SHIFT 13 #define PCAP_PC_MASK 0x001e0000 #define PCAP_PC_SHIFT 17 #define PCAP_VC_MASK 0x01e00000 #define PCAP_VC_SHIFT 21 #define PCAP_CC_MASK 0x1e000000 #define PCAP_CC_SHIFT 25 #define PCAP5_PC_MASK 0x003e0000 /* PMU corerev >= 5 */ #define PCAP5_PC_SHIFT 17 #define PCAP5_VC_MASK 0x07c00000 #define PCAP5_VC_SHIFT 22 #define PCAP5_CC_MASK 0xf8000000 #define PCAP5_CC_SHIFT 27 /* PMU Resource Request Timer registers */ /* This is based on PmuRev0 */ #define PRRT_TIME_MASK 0x03ff #define PRRT_INTEN 0x0400 #define PRRT_REQ_ACTIVE 0x0800 #define PRRT_ALP_REQ 0x1000 #define PRRT_HT_REQ 0x2000 #define PRRT_HQ_REQ 0x4000 /* PMU resource bit position */ #define PMURES_BIT(bit) (1 << (bit)) /* PMU resource number limit */ #define PMURES_MAX_RESNUM 30 /* PMU chip control0 register */ #define PMU_CHIPCTL0 0 #define PMU43143_CC0_SDIO_DRSTR_OVR (1 << 31) /* sdio drive strength override enable */ /* clock req types */ #define PMU_CC1_CLKREQ_TYPE_SHIFT 19 #define PMU_CC1_CLKREQ_TYPE_MASK (1 << PMU_CC1_CLKREQ_TYPE_SHIFT) #define CLKREQ_TYPE_CONFIG_OPENDRAIN 0 #define CLKREQ_TYPE_CONFIG_PUSHPULL 1 /* PMU chip control1 register */ #define PMU_CHIPCTL1 1 #define PMU_CC1_RXC_DLL_BYPASS 0x00010000 #define PMU_CC1_IF_TYPE_MASK 0x00000030 #define PMU_CC1_IF_TYPE_RMII 0x00000000 #define PMU_CC1_IF_TYPE_MII 0x00000010 #define PMU_CC1_IF_TYPE_RGMII 0x00000020 #define PMU_CC1_SW_TYPE_MASK 0x000000c0 #define PMU_CC1_SW_TYPE_EPHY 0x00000000 #define PMU_CC1_SW_TYPE_EPHYMII 0x00000040 #define PMU_CC1_SW_TYPE_EPHYRMII 0x00000080 #define PMU_CC1_SW_TYPE_RGMII 0x000000c0 /* PMU chip control2 register */ #define PMU_CHIPCTL2 2 /* PMU chip control3 register */ #define PMU_CHIPCTL3 3 #define PMU_CC3_ENABLE_SDIO_WAKEUP_SHIFT 19 #define PMU_CC3_ENABLE_RF_SHIFT 22 #define PMU_CC3_RF_DISABLE_IVALUE_SHIFT 23 /* PMU chip control5 register */ #define PMU_CHIPCTL5 5 /* PMU corerev and chip specific PLL controls. * PMU_PLL_XX where is PMU corerev and is an arbitrary number * to differentiate different PLLs controlled by the same PMU rev. */ /* pllcontrol registers */ /* PDIV, div_phy, div_arm, div_adc, dith_sel, ioff, kpd_scale, lsb_sel, mash_sel, lf_c & lf_r */ #define PMU0_PLL0_PLLCTL0 0 #define PMU0_PLL0_PC0_PDIV_MASK 1 #define PMU0_PLL0_PC0_PDIV_FREQ 25000 #define PMU0_PLL0_PC0_DIV_ARM_MASK 0x00000038 #define PMU0_PLL0_PC0_DIV_ARM_SHIFT 3 #define PMU0_PLL0_PC0_DIV_ARM_BASE 8 /* PC0_DIV_ARM for PLLOUT_ARM */ #define PMU0_PLL0_PC0_DIV_ARM_110MHZ 0 #define PMU0_PLL0_PC0_DIV_ARM_97_7MHZ 1 #define PMU0_PLL0_PC0_DIV_ARM_88MHZ 2 #define PMU0_PLL0_PC0_DIV_ARM_80MHZ 3 /* Default */ #define PMU0_PLL0_PC0_DIV_ARM_73_3MHZ 4 #define PMU0_PLL0_PC0_DIV_ARM_67_7MHZ 5 #define PMU0_PLL0_PC0_DIV_ARM_62_9MHZ 6 #define PMU0_PLL0_PC0_DIV_ARM_58_6MHZ 7 /* Wildcard base, stop_mod, en_lf_tp, en_cal & lf_r2 */ #define PMU0_PLL0_PLLCTL1 1 #define PMU0_PLL0_PC1_WILD_INT_MASK 0xf0000000 #define PMU0_PLL0_PC1_WILD_INT_SHIFT 28 #define PMU0_PLL0_PC1_WILD_FRAC_MASK 0x0fffff00 #define PMU0_PLL0_PC1_WILD_FRAC_SHIFT 8 #define PMU0_PLL0_PC1_STOP_MOD 0x00000040 /* Wildcard base, vco_calvar, vco_swc, vco_var_selref, vso_ical & vco_sel_avdd */ #define PMU0_PLL0_PLLCTL2 2 #define PMU0_PLL0_PC2_WILD_INT_MASK 0xf #define PMU0_PLL0_PC2_WILD_INT_SHIFT 4 /* pllcontrol registers */ /* ndiv_pwrdn, pwrdn_ch, refcomp_pwrdn, dly_ch, p1div, p2div, _bypass_sdmod */ #define PMU1_PLL0_PLLCTL0 0 #define PMU1_PLL0_PC0_P1DIV_MASK 0x00f00000 #define PMU1_PLL0_PC0_P1DIV_SHIFT 20 #define PMU1_PLL0_PC0_P2DIV_MASK 0x0f000000 #define PMU1_PLL0_PC0_P2DIV_SHIFT 24 /* mdiv */ #define PMU1_PLL0_PLLCTL1 1 #define PMU1_PLL0_PC1_M1DIV_MASK 0x000000ff #define PMU1_PLL0_PC1_M1DIV_SHIFT 0 #define PMU1_PLL0_PC1_M2DIV_MASK 0x0000ff00 #define PMU1_PLL0_PC1_M2DIV_SHIFT 8 #define PMU1_PLL0_PC1_M3DIV_MASK 0x00ff0000 #define PMU1_PLL0_PC1_M3DIV_SHIFT 16 #define PMU1_PLL0_PC1_M4DIV_MASK 0xff000000 #define PMU1_PLL0_PC1_M4DIV_SHIFT 24 #define PMU1_PLL0_PC1_M4DIV_BY_9 9 #define PMU1_PLL0_PC1_M4DIV_BY_18 0x12 #define PMU1_PLL0_PC1_M4DIV_BY_36 0x24 #define DOT11MAC_880MHZ_CLK_DIVISOR_SHIFT 8 #define DOT11MAC_880MHZ_CLK_DIVISOR_MASK (0xFF << DOT11MAC_880MHZ_CLK_DIVISOR_SHIFT) #define DOT11MAC_880MHZ_CLK_DIVISOR_VAL (0xE << DOT11MAC_880MHZ_CLK_DIVISOR_SHIFT) /* mdiv, ndiv_dither_mfb, ndiv_mode, ndiv_int */ #define PMU1_PLL0_PLLCTL2 2 #define PMU1_PLL0_PC2_M5DIV_MASK 0x000000ff #define PMU1_PLL0_PC2_M5DIV_SHIFT 0 #define PMU1_PLL0_PC2_M5DIV_BY_12 0xc #define PMU1_PLL0_PC2_M5DIV_BY_18 0x12 #define PMU1_PLL0_PC2_M5DIV_BY_36 0x24 #define PMU1_PLL0_PC2_M6DIV_MASK 0x0000ff00 #define PMU1_PLL0_PC2_M6DIV_SHIFT 8 #define PMU1_PLL0_PC2_M6DIV_BY_18 0x12 #define PMU1_PLL0_PC2_M6DIV_BY_36 0x24 #define PMU1_PLL0_PC2_NDIV_MODE_MASK 0x000e0000 #define PMU1_PLL0_PC2_NDIV_MODE_SHIFT 17 #define PMU1_PLL0_PC2_NDIV_MODE_MASH 1 #define PMU1_PLL0_PC2_NDIV_MODE_MFB 2 /* recommended for 4319 */ #define PMU1_PLL0_PC2_NDIV_INT_MASK 0x1ff00000 #define PMU1_PLL0_PC2_NDIV_INT_SHIFT 20 /* ndiv_frac */ #define PMU1_PLL0_PLLCTL3 3 #define PMU1_PLL0_PC3_NDIV_FRAC_MASK 0x00ffffff #define PMU1_PLL0_PC3_NDIV_FRAC_SHIFT 0 /* pll_ctrl */ #define PMU1_PLL0_PLLCTL4 4 /* pll_ctrl, vco_rng, clkdrive_ch */ #define PMU1_PLL0_PLLCTL5 5 #define PMU1_PLL0_PC5_CLK_DRV_MASK 0xffffff00 #define PMU1_PLL0_PC5_CLK_DRV_SHIFT 8 /* PMU rev 2 control words */ #define PMU2_PHY_PLL_PLLCTL 4 #define PMU2_SI_PLL_PLLCTL 10 /* PMU rev 2 */ /* pllcontrol registers */ /* ndiv_pwrdn, pwrdn_ch, refcomp_pwrdn, dly_ch, p1div, p2div, _bypass_sdmod */ #define PMU2_PLL_PLLCTL0 0 #define PMU2_PLL_PC0_P1DIV_MASK 0x00f00000 #define PMU2_PLL_PC0_P1DIV_SHIFT 20 #define PMU2_PLL_PC0_P2DIV_MASK 0x0f000000 #define PMU2_PLL_PC0_P2DIV_SHIFT 24 /* mdiv */ #define PMU2_PLL_PLLCTL1 1 #define PMU2_PLL_PC1_M1DIV_MASK 0x000000ff #define PMU2_PLL_PC1_M1DIV_SHIFT 0 #define PMU2_PLL_PC1_M2DIV_MASK 0x0000ff00 #define PMU2_PLL_PC1_M2DIV_SHIFT 8 #define PMU2_PLL_PC1_M3DIV_MASK 0x00ff0000 #define PMU2_PLL_PC1_M3DIV_SHIFT 16 #define PMU2_PLL_PC1_M4DIV_MASK 0xff000000 #define PMU2_PLL_PC1_M4DIV_SHIFT 24 /* mdiv, ndiv_dither_mfb, ndiv_mode, ndiv_int */ #define PMU2_PLL_PLLCTL2 2 #define PMU2_PLL_PC2_M5DIV_MASK 0x000000ff #define PMU2_PLL_PC2_M5DIV_SHIFT 0 #define PMU2_PLL_PC2_M6DIV_MASK 0x0000ff00 #define PMU2_PLL_PC2_M6DIV_SHIFT 8 #define PMU2_PLL_PC2_NDIV_MODE_MASK 0x000e0000 #define PMU2_PLL_PC2_NDIV_MODE_SHIFT 17 #define PMU2_PLL_PC2_NDIV_INT_MASK 0x1ff00000 #define PMU2_PLL_PC2_NDIV_INT_SHIFT 20 /* ndiv_frac */ #define PMU2_PLL_PLLCTL3 3 #define PMU2_PLL_PC3_NDIV_FRAC_MASK 0x00ffffff #define PMU2_PLL_PC3_NDIV_FRAC_SHIFT 0 /* pll_ctrl */ #define PMU2_PLL_PLLCTL4 4 /* pll_ctrl, vco_rng, clkdrive_ch */ #define PMU2_PLL_PLLCTL5 5 #define PMU2_PLL_PC5_CLKDRIVE_CH1_MASK 0x00000f00 #define PMU2_PLL_PC5_CLKDRIVE_CH1_SHIFT 8 #define PMU2_PLL_PC5_CLKDRIVE_CH2_MASK 0x0000f000 #define PMU2_PLL_PC5_CLKDRIVE_CH2_SHIFT 12 #define PMU2_PLL_PC5_CLKDRIVE_CH3_MASK 0x000f0000 #define PMU2_PLL_PC5_CLKDRIVE_CH3_SHIFT 16 #define PMU2_PLL_PC5_CLKDRIVE_CH4_MASK 0x00f00000 #define PMU2_PLL_PC5_CLKDRIVE_CH4_SHIFT 20 #define PMU2_PLL_PC5_CLKDRIVE_CH5_MASK 0x0f000000 #define PMU2_PLL_PC5_CLKDRIVE_CH5_SHIFT 24 #define PMU2_PLL_PC5_CLKDRIVE_CH6_MASK 0xf0000000 #define PMU2_PLL_PC5_CLKDRIVE_CH6_SHIFT 28 /* PMU rev 5 (& 6) */ #define PMU5_PLL_P1P2_OFF 0 #define PMU5_PLL_P1_MASK 0x0f000000 #define PMU5_PLL_P1_SHIFT 24 #define PMU5_PLL_P2_MASK 0x00f00000 #define PMU5_PLL_P2_SHIFT 20 #define PMU5_PLL_M14_OFF 1 #define PMU5_PLL_MDIV_MASK 0x000000ff #define PMU5_PLL_MDIV_WIDTH 8 #define PMU5_PLL_NM5_OFF 2 #define PMU5_PLL_NDIV_MASK 0xfff00000 #define PMU5_PLL_NDIV_SHIFT 20 #define PMU5_PLL_NDIV_MODE_MASK 0x000e0000 #define PMU5_PLL_NDIV_MODE_SHIFT 17 #define PMU5_PLL_FMAB_OFF 3 #define PMU5_PLL_MRAT_MASK 0xf0000000 #define PMU5_PLL_MRAT_SHIFT 28 #define PMU5_PLL_ABRAT_MASK 0x08000000 #define PMU5_PLL_ABRAT_SHIFT 27 #define PMU5_PLL_FDIV_MASK 0x07ffffff #define PMU5_PLL_PLLCTL_OFF 4 #define PMU5_PLL_PCHI_OFF 5 #define PMU5_PLL_PCHI_MASK 0x0000003f /* pmu XtalFreqRatio */ #define PMU_XTALFREQ_REG_ILPCTR_MASK 0x00001FFF #define PMU_XTALFREQ_REG_MEASURE_MASK 0x80000000 #define PMU_XTALFREQ_REG_MEASURE_SHIFT 31 /* Divider allocation in 4716/47162/5356/5357 */ #define PMU5_MAINPLL_CPU 1 #define PMU5_MAINPLL_MEM 2 #define PMU5_MAINPLL_SI 3 /* 4706 PMU */ #define PMU4706_MAINPLL_PLL0 0 #define PMU6_4706_PROCPLL_OFF 4 /* The CPU PLL */ #define PMU6_4706_PROC_P2DIV_MASK 0x000f0000 #define PMU6_4706_PROC_P2DIV_SHIFT 16 #define PMU6_4706_PROC_P1DIV_MASK 0x0000f000 #define PMU6_4706_PROC_P1DIV_SHIFT 12 #define PMU6_4706_PROC_NDIV_INT_MASK 0x00000ff8 #define PMU6_4706_PROC_NDIV_INT_SHIFT 3 #define PMU6_4706_PROC_NDIV_MODE_MASK 0x00000007 #define PMU6_4706_PROC_NDIV_MODE_SHIFT 0 #define PMU7_PLL_PLLCTL7 7 #define PMU7_PLL_CTL7_M4DIV_MASK 0xff000000 #define PMU7_PLL_CTL7_M4DIV_SHIFT 24 #define PMU7_PLL_CTL7_M4DIV_BY_6 6 #define PMU7_PLL_CTL7_M4DIV_BY_12 0xc #define PMU7_PLL_CTL7_M4DIV_BY_24 0x18 #define PMU7_PLL_PLLCTL8 8 #define PMU7_PLL_CTL8_M5DIV_MASK 0x000000ff #define PMU7_PLL_CTL8_M5DIV_SHIFT 0 #define PMU7_PLL_CTL8_M5DIV_BY_8 8 #define PMU7_PLL_CTL8_M5DIV_BY_12 0xc #define PMU7_PLL_CTL8_M5DIV_BY_24 0x18 #define PMU7_PLL_CTL8_M6DIV_MASK 0x0000ff00 #define PMU7_PLL_CTL8_M6DIV_SHIFT 8 #define PMU7_PLL_CTL8_M6DIV_BY_12 0xc #define PMU7_PLL_CTL8_M6DIV_BY_24 0x18 #define PMU7_PLL_PLLCTL11 11 #define PMU7_PLL_PLLCTL11_MASK 0xffffff00 #define PMU7_PLL_PLLCTL11_VAL 0x22222200 /* PMU rev 15 */ #define PMU15_PLL_PLLCTL0 0 #define PMU15_PLL_PC0_CLKSEL_MASK 0x00000003 #define PMU15_PLL_PC0_CLKSEL_SHIFT 0 #define PMU15_PLL_PC0_FREQTGT_MASK 0x003FFFFC #define PMU15_PLL_PC0_FREQTGT_SHIFT 2 #define PMU15_PLL_PC0_PRESCALE_MASK 0x00C00000 #define PMU15_PLL_PC0_PRESCALE_SHIFT 22 #define PMU15_PLL_PC0_KPCTRL_MASK 0x07000000 #define PMU15_PLL_PC0_KPCTRL_SHIFT 24 #define PMU15_PLL_PC0_FCNTCTRL_MASK 0x38000000 #define PMU15_PLL_PC0_FCNTCTRL_SHIFT 27 #define PMU15_PLL_PC0_FDCMODE_MASK 0x40000000 #define PMU15_PLL_PC0_FDCMODE_SHIFT 30 #define PMU15_PLL_PC0_CTRLBIAS_MASK 0x80000000 #define PMU15_PLL_PC0_CTRLBIAS_SHIFT 31 #define PMU15_PLL_PLLCTL1 1 #define PMU15_PLL_PC1_BIAS_CTLM_MASK 0x00000060 #define PMU15_PLL_PC1_BIAS_CTLM_SHIFT 5 #define PMU15_PLL_PC1_BIAS_CTLM_RST_MASK 0x00000040 #define PMU15_PLL_PC1_BIAS_CTLM_RST_SHIFT 6 #define PMU15_PLL_PC1_BIAS_SS_DIVR_MASK 0x0001FF80 #define PMU15_PLL_PC1_BIAS_SS_DIVR_SHIFT 7 #define PMU15_PLL_PC1_BIAS_SS_RSTVAL_MASK 0x03FE0000 #define PMU15_PLL_PC1_BIAS_SS_RSTVAL_SHIFT 17 #define PMU15_PLL_PC1_BIAS_INTG_BW_MASK 0x0C000000 #define PMU15_PLL_PC1_BIAS_INTG_BW_SHIFT 26 #define PMU15_PLL_PC1_BIAS_INTG_BYP_MASK 0x10000000 #define PMU15_PLL_PC1_BIAS_INTG_BYP_SHIFT 28 #define PMU15_PLL_PC1_OPENLP_EN_MASK 0x40000000 #define PMU15_PLL_PC1_OPENLP_EN_SHIFT 30 #define PMU15_PLL_PLLCTL2 2 #define PMU15_PLL_PC2_CTEN_MASK 0x00000001 #define PMU15_PLL_PC2_CTEN_SHIFT 0 #define PMU15_PLL_PLLCTL3 3 #define PMU15_PLL_PC3_DITHER_EN_MASK 0x00000001 #define PMU15_PLL_PC3_DITHER_EN_SHIFT 0 #define PMU15_PLL_PC3_DCOCTLSP_MASK 0xFE000000 #define PMU15_PLL_PC3_DCOCTLSP_SHIFT 25 #define PMU15_PLL_PC3_DCOCTLSP_DIV2EN_MASK 0x01 #define PMU15_PLL_PC3_DCOCTLSP_DIV2EN_SHIFT 0 #define PMU15_PLL_PC3_DCOCTLSP_CH0EN_MASK 0x02 #define PMU15_PLL_PC3_DCOCTLSP_CH0EN_SHIFT 1 #define PMU15_PLL_PC3_DCOCTLSP_CH1EN_MASK 0x04 #define PMU15_PLL_PC3_DCOCTLSP_CH1EN_SHIFT 2 #define PMU15_PLL_PC3_DCOCTLSP_CH0SEL_MASK 0x18 #define PMU15_PLL_PC3_DCOCTLSP_CH0SEL_SHIFT 3 #define PMU15_PLL_PC3_DCOCTLSP_CH1SEL_MASK 0x60 #define PMU15_PLL_PC3_DCOCTLSP_CH1SEL_SHIFT 5 #define PMU15_PLL_PC3_DCOCTLSP_CHSEL_OUTP_DIV1 0 #define PMU15_PLL_PC3_DCOCTLSP_CHSEL_OUTP_DIV2 1 #define PMU15_PLL_PC3_DCOCTLSP_CHSEL_OUTP_DIV3 2 #define PMU15_PLL_PC3_DCOCTLSP_CHSEL_OUTP_DIV5 3 #define PMU15_PLL_PLLCTL4 4 #define PMU15_PLL_PC4_FLLCLK1_DIV_MASK 0x00000007 #define PMU15_PLL_PC4_FLLCLK1_DIV_SHIFT 0 #define PMU15_PLL_PC4_FLLCLK2_DIV_MASK 0x00000038 #define PMU15_PLL_PC4_FLLCLK2_DIV_SHIFT 3 #define PMU15_PLL_PC4_FLLCLK3_DIV_MASK 0x000001C0 #define PMU15_PLL_PC4_FLLCLK3_DIV_SHIFT 6 #define PMU15_PLL_PC4_DBGMODE_MASK 0x00000E00 #define PMU15_PLL_PC4_DBGMODE_SHIFT 9 #define PMU15_PLL_PC4_FLL480_CTLSP_LK_MASK 0x00001000 #define PMU15_PLL_PC4_FLL480_CTLSP_LK_SHIFT 12 #define PMU15_PLL_PC4_FLL480_CTLSP_MASK 0x000FE000 #define PMU15_PLL_PC4_FLL480_CTLSP_SHIFT 13 #define PMU15_PLL_PC4_DINPOL_MASK 0x00100000 #define PMU15_PLL_PC4_DINPOL_SHIFT 20 #define PMU15_PLL_PC4_CLKOUT_PD_MASK 0x00200000 #define PMU15_PLL_PC4_CLKOUT_PD_SHIFT 21 #define PMU15_PLL_PC4_CLKDIV2_PD_MASK 0x00400000 #define PMU15_PLL_PC4_CLKDIV2_PD_SHIFT 22 #define PMU15_PLL_PC4_CLKDIV4_PD_MASK 0x00800000 #define PMU15_PLL_PC4_CLKDIV4_PD_SHIFT 23 #define PMU15_PLL_PC4_CLKDIV8_PD_MASK 0x01000000 #define PMU15_PLL_PC4_CLKDIV8_PD_SHIFT 24 #define PMU15_PLL_PC4_CLKDIV16_PD_MASK 0x02000000 #define PMU15_PLL_PC4_CLKDIV16_PD_SHIFT 25 #define PMU15_PLL_PC4_TEST_EN_MASK 0x04000000 #define PMU15_PLL_PC4_TEST_EN_SHIFT 26 #define PMU15_PLL_PLLCTL5 5 #define PMU15_PLL_PC5_FREQTGT_MASK 0x000FFFFF #define PMU15_PLL_PC5_FREQTGT_SHIFT 0 #define PMU15_PLL_PC5_DCOCTLSP_MASK 0x07F00000 #define PMU15_PLL_PC5_DCOCTLSP_SHIFT 20 #define PMU15_PLL_PC5_PRESCALE_MASK 0x18000000 #define PMU15_PLL_PC5_PRESCALE_SHIFT 27 #define PMU15_PLL_PLLCTL6 6 #define PMU15_PLL_PC6_FREQTGT_MASK 0x000FFFFF #define PMU15_PLL_PC6_FREQTGT_SHIFT 0 #define PMU15_PLL_PC6_DCOCTLSP_MASK 0x07F00000 #define PMU15_PLL_PC6_DCOCTLSP_SHIFT 20 #define PMU15_PLL_PC6_PRESCALE_MASK 0x18000000 #define PMU15_PLL_PC6_PRESCALE_SHIFT 27 #define PMU15_FREQTGT_480_DEFAULT 0x19AB1 #define PMU15_FREQTGT_492_DEFAULT 0x1A4F5 #define PMU15_ARM_96MHZ 96000000 /* 96 Mhz */ #define PMU15_ARM_98MHZ 98400000 /* 98.4 Mhz */ #define PMU15_ARM_97MHZ 97000000 /* 97 Mhz */ #define PMU17_PLLCTL2_NDIVTYPE_MASK 0x00000070 #define PMU17_PLLCTL2_NDIVTYPE_SHIFT 4 #define PMU17_PLLCTL2_NDIV_MODE_INT 0 #define PMU17_PLLCTL2_NDIV_MODE_INT1B8 1 #define PMU17_PLLCTL2_NDIV_MODE_MASH111 2 #define PMU17_PLLCTL2_NDIV_MODE_MASH111B8 3 #define PMU17_PLLCTL0_BBPLL_PWRDWN 0 #define PMU17_PLLCTL0_BBPLL_DRST 3 #define PMU17_PLLCTL0_BBPLL_DISBL_CLK 8 /* PLL usage in 4716/47162 */ #define PMU4716_MAINPLL_PLL0 12 /* PLL usage in 5356/5357 */ #define PMU5356_MAINPLL_PLL0 0 #define PMU5357_MAINPLL_PLL0 0 /* 4716/47162 resources */ #define RES4716_PROC_PLL_ON 0x00000040 #define RES4716_PROC_HT_AVAIL 0x00000080 /* 4716/4717/4718 Chip specific ChipControl register bits */ #define CCTRL_471X_I2S_PINS_ENABLE 0x0080 /* I2S pins off by default, shared w/ pflash */ /* 5357 Chip specific ChipControl register bits */ /* 2nd - 32-bit reg */ #define CCTRL_5357_I2S_PINS_ENABLE 0x00040000 /* I2S pins enable */ #define CCTRL_5357_I2CSPI_PINS_ENABLE 0x00080000 /* I2C/SPI pins enable */ /* 5354 resources */ #define RES5354_EXT_SWITCHER_PWM 0 /* 0x00001 */ #define RES5354_BB_SWITCHER_PWM 1 /* 0x00002 */ #define RES5354_BB_SWITCHER_BURST 2 /* 0x00004 */ #define RES5354_BB_EXT_SWITCHER_BURST 3 /* 0x00008 */ #define RES5354_ILP_REQUEST 4 /* 0x00010 */ #define RES5354_RADIO_SWITCHER_PWM 5 /* 0x00020 */ #define RES5354_RADIO_SWITCHER_BURST 6 /* 0x00040 */ #define RES5354_ROM_SWITCH 7 /* 0x00080 */ #define RES5354_PA_REF_LDO 8 /* 0x00100 */ #define RES5354_RADIO_LDO 9 /* 0x00200 */ #define RES5354_AFE_LDO 10 /* 0x00400 */ #define RES5354_PLL_LDO 11 /* 0x00800 */ #define RES5354_BG_FILTBYP 12 /* 0x01000 */ #define RES5354_TX_FILTBYP 13 /* 0x02000 */ #define RES5354_RX_FILTBYP 14 /* 0x04000 */ #define RES5354_XTAL_PU 15 /* 0x08000 */ #define RES5354_XTAL_EN 16 /* 0x10000 */ #define RES5354_BB_PLL_FILTBYP 17 /* 0x20000 */ #define RES5354_RF_PLL_FILTBYP 18 /* 0x40000 */ #define RES5354_BB_PLL_PU 19 /* 0x80000 */ /* 5357 Chip specific ChipControl register bits */ #define CCTRL5357_EXTPA (1<<14) /* extPA in ChipControl 1, bit 14 */ #define CCTRL5357_ANT_MUX_2o3 (1<<15) /* 2o3 in ChipControl 1, bit 15 */ #define CCTRL5357_NFLASH (1<<16) /* Nandflash in ChipControl 1, bit 16 */ /* 43217 Chip specific ChipControl register bits */ #define CCTRL43217_EXTPA_C0 (1<<13) /* core0 extPA in ChipControl 1, bit 13 */ #define CCTRL43217_EXTPA_C1 (1<<8) /* core1 extPA in ChipControl 1, bit 8 */ /* 43228 Chip specific ChipControl register bits */ #define CCTRL43228_EXTPA_C0 (1<<14) /* core1 extPA in ChipControl 1, bit 14 */ #define CCTRL43228_EXTPA_C1 (1<<9) /* core0 extPA in ChipControl 1, bit 1 */ /* 4328 resources */ #define RES4328_EXT_SWITCHER_PWM 0 /* 0x00001 */ #define RES4328_BB_SWITCHER_PWM 1 /* 0x00002 */ #define RES4328_BB_SWITCHER_BURST 2 /* 0x00004 */ #define RES4328_BB_EXT_SWITCHER_BURST 3 /* 0x00008 */ #define RES4328_ILP_REQUEST 4 /* 0x00010 */ #define RES4328_RADIO_SWITCHER_PWM 5 /* 0x00020 */ #define RES4328_RADIO_SWITCHER_BURST 6 /* 0x00040 */ #define RES4328_ROM_SWITCH 7 /* 0x00080 */ #define RES4328_PA_REF_LDO 8 /* 0x00100 */ #define RES4328_RADIO_LDO 9 /* 0x00200 */ #define RES4328_AFE_LDO 10 /* 0x00400 */ #define RES4328_PLL_LDO 11 /* 0x00800 */ #define RES4328_BG_FILTBYP 12 /* 0x01000 */ #define RES4328_TX_FILTBYP 13 /* 0x02000 */ #define RES4328_RX_FILTBYP 14 /* 0x04000 */ #define RES4328_XTAL_PU 15 /* 0x08000 */ #define RES4328_XTAL_EN 16 /* 0x10000 */ #define RES4328_BB_PLL_FILTBYP 17 /* 0x20000 */ #define RES4328_RF_PLL_FILTBYP 18 /* 0x40000 */ #define RES4328_BB_PLL_PU 19 /* 0x80000 */ /* 4325 A0/A1 resources */ #define RES4325_BUCK_BOOST_BURST 0 /* 0x00000001 */ #define RES4325_CBUCK_BURST 1 /* 0x00000002 */ #define RES4325_CBUCK_PWM 2 /* 0x00000004 */ #define RES4325_CLDO_CBUCK_BURST 3 /* 0x00000008 */ #define RES4325_CLDO_CBUCK_PWM 4 /* 0x00000010 */ #define RES4325_BUCK_BOOST_PWM 5 /* 0x00000020 */ #define RES4325_ILP_REQUEST 6 /* 0x00000040 */ #define RES4325_ABUCK_BURST 7 /* 0x00000080 */ #define RES4325_ABUCK_PWM 8 /* 0x00000100 */ #define RES4325_LNLDO1_PU 9 /* 0x00000200 */ #define RES4325_OTP_PU 10 /* 0x00000400 */ #define RES4325_LNLDO3_PU 11 /* 0x00000800 */ #define RES4325_LNLDO4_PU 12 /* 0x00001000 */ #define RES4325_XTAL_PU 13 /* 0x00002000 */ #define RES4325_ALP_AVAIL 14 /* 0x00004000 */ #define RES4325_RX_PWRSW_PU 15 /* 0x00008000 */ #define RES4325_TX_PWRSW_PU 16 /* 0x00010000 */ #define RES4325_RFPLL_PWRSW_PU 17 /* 0x00020000 */ #define RES4325_LOGEN_PWRSW_PU 18 /* 0x00040000 */ #define RES4325_AFE_PWRSW_PU 19 /* 0x00080000 */ #define RES4325_BBPLL_PWRSW_PU 20 /* 0x00100000 */ #define RES4325_HT_AVAIL 21 /* 0x00200000 */ /* 4325 B0/C0 resources */ #define RES4325B0_CBUCK_LPOM 1 /* 0x00000002 */ #define RES4325B0_CBUCK_BURST 2 /* 0x00000004 */ #define RES4325B0_CBUCK_PWM 3 /* 0x00000008 */ #define RES4325B0_CLDO_PU 4 /* 0x00000010 */ /* 4325 C1 resources */ #define RES4325C1_LNLDO2_PU 12 /* 0x00001000 */ /* 4325 chip-specific ChipStatus register bits */ #define CST4325_SPROM_OTP_SEL_MASK 0x00000003 #define CST4325_DEFCIS_SEL 0 /* OTP is powered up, use def. CIS, no SPROM */ #define CST4325_SPROM_SEL 1 /* OTP is powered up, SPROM is present */ #define CST4325_OTP_SEL 2 /* OTP is powered up, no SPROM */ #define CST4325_OTP_PWRDN 3 /* OTP is powered down, SPROM is present */ #define CST4325_SDIO_USB_MODE_MASK 0x00000004 #define CST4325_SDIO_USB_MODE_SHIFT 2 #define CST4325_RCAL_VALID_MASK 0x00000008 #define CST4325_RCAL_VALID_SHIFT 3 #define CST4325_RCAL_VALUE_MASK 0x000001f0 #define CST4325_RCAL_VALUE_SHIFT 4 #define CST4325_PMUTOP_2B_MASK 0x00000200 /* 1 for 2b, 0 for to 2a */ #define CST4325_PMUTOP_2B_SHIFT 9 #define RES4329_RESERVED0 0 /* 0x00000001 */ #define RES4329_CBUCK_LPOM 1 /* 0x00000002 */ #define RES4329_CBUCK_BURST 2 /* 0x00000004 */ #define RES4329_CBUCK_PWM 3 /* 0x00000008 */ #define RES4329_CLDO_PU 4 /* 0x00000010 */ #define RES4329_PALDO_PU 5 /* 0x00000020 */ #define RES4329_ILP_REQUEST 6 /* 0x00000040 */ #define RES4329_RESERVED7 7 /* 0x00000080 */ #define RES4329_RESERVED8 8 /* 0x00000100 */ #define RES4329_LNLDO1_PU 9 /* 0x00000200 */ #define RES4329_OTP_PU 10 /* 0x00000400 */ #define RES4329_RESERVED11 11 /* 0x00000800 */ #define RES4329_LNLDO2_PU 12 /* 0x00001000 */ #define RES4329_XTAL_PU 13 /* 0x00002000 */ #define RES4329_ALP_AVAIL 14 /* 0x00004000 */ #define RES4329_RX_PWRSW_PU 15 /* 0x00008000 */ #define RES4329_TX_PWRSW_PU 16 /* 0x00010000 */ #define RES4329_RFPLL_PWRSW_PU 17 /* 0x00020000 */ #define RES4329_LOGEN_PWRSW_PU 18 /* 0x00040000 */ #define RES4329_AFE_PWRSW_PU 19 /* 0x00080000 */ #define RES4329_BBPLL_PWRSW_PU 20 /* 0x00100000 */ #define RES4329_HT_AVAIL 21 /* 0x00200000 */ #define CST4329_SPROM_OTP_SEL_MASK 0x00000003 #define CST4329_DEFCIS_SEL 0 /* OTP is powered up, use def. CIS, no SPROM */ #define CST4329_SPROM_SEL 1 /* OTP is powered up, SPROM is present */ #define CST4329_OTP_SEL 2 /* OTP is powered up, no SPROM */ #define CST4329_OTP_PWRDN 3 /* OTP is powered down, SPROM is present */ #define CST4329_SPI_SDIO_MODE_MASK 0x00000004 #define CST4329_SPI_SDIO_MODE_SHIFT 2 /* 4312 chip-specific ChipStatus register bits */ #define CST4312_SPROM_OTP_SEL_MASK 0x00000003 #define CST4312_DEFCIS_SEL 0 /* OTP is powered up, use def. CIS, no SPROM */ #define CST4312_SPROM_SEL 1 /* OTP is powered up, SPROM is present */ #define CST4312_OTP_SEL 2 /* OTP is powered up, no SPROM */ #define CST4312_OTP_BAD 3 /* OTP is broken, SPROM is present */ /* 4312 resources (all PMU chips with little memory constraint) */ #define RES4312_SWITCHER_BURST 0 /* 0x00000001 */ #define RES4312_SWITCHER_PWM 1 /* 0x00000002 */ #define RES4312_PA_REF_LDO 2 /* 0x00000004 */ #define RES4312_CORE_LDO_BURST 3 /* 0x00000008 */ #define RES4312_CORE_LDO_PWM 4 /* 0x00000010 */ #define RES4312_RADIO_LDO 5 /* 0x00000020 */ #define RES4312_ILP_REQUEST 6 /* 0x00000040 */ #define RES4312_BG_FILTBYP 7 /* 0x00000080 */ #define RES4312_TX_FILTBYP 8 /* 0x00000100 */ #define RES4312_RX_FILTBYP 9 /* 0x00000200 */ #define RES4312_XTAL_PU 10 /* 0x00000400 */ #define RES4312_ALP_AVAIL 11 /* 0x00000800 */ #define RES4312_BB_PLL_FILTBYP 12 /* 0x00001000 */ #define RES4312_RF_PLL_FILTBYP 13 /* 0x00002000 */ #define RES4312_HT_AVAIL 14 /* 0x00004000 */ /* 4322 resources */ #define RES4322_RF_LDO 0 #define RES4322_ILP_REQUEST 1 #define RES4322_XTAL_PU 2 #define RES4322_ALP_AVAIL 3 #define RES4322_SI_PLL_ON 4 #define RES4322_HT_SI_AVAIL 5 #define RES4322_PHY_PLL_ON 6 #define RES4322_HT_PHY_AVAIL 7 #define RES4322_OTP_PU 8 /* 4322 chip-specific ChipStatus register bits */ #define CST4322_XTAL_FREQ_20_40MHZ 0x00000020 #define CST4322_SPROM_OTP_SEL_MASK 0x000000c0 #define CST4322_SPROM_OTP_SEL_SHIFT 6 #define CST4322_NO_SPROM_OTP 0 /* no OTP, no SPROM */ #define CST4322_SPROM_PRESENT 1 /* SPROM is present */ #define CST4322_OTP_PRESENT 2 /* OTP is present */ #define CST4322_PCI_OR_USB 0x00000100 #define CST4322_BOOT_MASK 0x00000600 #define CST4322_BOOT_SHIFT 9 #define CST4322_BOOT_FROM_SRAM 0 /* boot from SRAM, ARM in reset */ #define CST4322_BOOT_FROM_ROM 1 /* boot from ROM */ #define CST4322_BOOT_FROM_FLASH 2 /* boot from FLASH */ #define CST4322_BOOT_FROM_INVALID 3 #define CST4322_ILP_DIV_EN 0x00000800 #define CST4322_FLASH_TYPE_MASK 0x00001000 #define CST4322_FLASH_TYPE_SHIFT 12 #define CST4322_FLASH_TYPE_SHIFT_ST 0 /* ST serial FLASH */ #define CST4322_FLASH_TYPE_SHIFT_ATMEL 1 /* ATMEL flash */ #define CST4322_ARM_TAP_SEL 0x00002000 #define CST4322_RES_INIT_MODE_MASK 0x0000c000 #define CST4322_RES_INIT_MODE_SHIFT 14 #define CST4322_RES_INIT_MODE_ILPAVAIL 0 /* resinitmode: ILP available */ #define CST4322_RES_INIT_MODE_ILPREQ 1 /* resinitmode: ILP request */ #define CST4322_RES_INIT_MODE_ALPAVAIL 2 /* resinitmode: ALP available */ #define CST4322_RES_INIT_MODE_HTAVAIL 3 /* resinitmode: HT available */ #define CST4322_PCIPLLCLK_GATING 0x00010000 #define CST4322_CLK_SWITCH_PCI_TO_ALP 0x00020000 #define CST4322_PCI_CARDBUS_MODE 0x00040000 /* 43224 chip-specific ChipControl register bits */ #define CCTRL43224_GPIO_TOGGLE 0x8000 /* gpio[3:0] pins as btcoex or s/w gpio */ #define CCTRL_43224A0_12MA_LED_DRIVE 0x00F000F0 /* 12 mA drive strength */ #define CCTRL_43224B0_12MA_LED_DRIVE 0xF0 /* 12 mA drive strength for later 43224s */ /* 43236 resources */ #define RES43236_REGULATOR 0 #define RES43236_ILP_REQUEST 1 #define RES43236_XTAL_PU 2 #define RES43236_ALP_AVAIL 3 #define RES43236_SI_PLL_ON 4 #define RES43236_HT_SI_AVAIL 5 /* 43236 chip-specific ChipControl register bits */ #define CCTRL43236_BT_COEXIST (1<<0) /* 0 disable */ #define CCTRL43236_SECI (1<<1) /* 0 SECI is disabled (JATG functional) */ #define CCTRL43236_EXT_LNA (1<<2) /* 0 disable */ #define CCTRL43236_ANT_MUX_2o3 (1<<3) /* 2o3 mux, chipcontrol bit 3 */ #define CCTRL43236_GSIO (1<<4) /* 0 disable */ /* 43236 Chip specific ChipStatus register bits */ #define CST43236_SFLASH_MASK 0x00000040 #define CST43236_OTP_SEL_MASK 0x00000080 #define CST43236_OTP_SEL_SHIFT 7 #define CST43236_HSIC_MASK 0x00000100 /* USB/HSIC */ #define CST43236_BP_CLK 0x00000200 /* 120/96Mbps */ #define CST43236_BOOT_MASK 0x00001800 #define CST43236_BOOT_SHIFT 11 #define CST43236_BOOT_FROM_SRAM 0 /* boot from SRAM, ARM in reset */ #define CST43236_BOOT_FROM_ROM 1 /* boot from ROM */ #define CST43236_BOOT_FROM_FLASH 2 /* boot from FLASH */ #define CST43236_BOOT_FROM_INVALID 3 /* 43237 resources */ #define RES43237_REGULATOR 0 #define RES43237_ILP_REQUEST 1 #define RES43237_XTAL_PU 2 #define RES43237_ALP_AVAIL 3 #define RES43237_SI_PLL_ON 4 #define RES43237_HT_SI_AVAIL 5 /* 43237 chip-specific ChipControl register bits */ #define CCTRL43237_BT_COEXIST (1<<0) /* 0 disable */ #define CCTRL43237_SECI (1<<1) /* 0 SECI is disabled (JATG functional) */ #define CCTRL43237_EXT_LNA (1<<2) /* 0 disable */ #define CCTRL43237_ANT_MUX_2o3 (1<<3) /* 2o3 mux, chipcontrol bit 3 */ #define CCTRL43237_GSIO (1<<4) /* 0 disable */ /* 43237 Chip specific ChipStatus register bits */ #define CST43237_SFLASH_MASK 0x00000040 #define CST43237_OTP_SEL_MASK 0x00000080 #define CST43237_OTP_SEL_SHIFT 7 #define CST43237_HSIC_MASK 0x00000100 /* USB/HSIC */ #define CST43237_BP_CLK 0x00000200 /* 120/96Mbps */ #define CST43237_BOOT_MASK 0x00001800 #define CST43237_BOOT_SHIFT 11 #define CST43237_BOOT_FROM_SRAM 0 /* boot from SRAM, ARM in reset */ #define CST43237_BOOT_FROM_ROM 1 /* boot from ROM */ #define CST43237_BOOT_FROM_FLASH 2 /* boot from FLASH */ #define CST43237_BOOT_FROM_INVALID 3 /* 43239 resources */ #define RES43239_OTP_PU 9 #define RES43239_MACPHY_CLKAVAIL 23 #define RES43239_HT_AVAIL 24 /* 43239 Chip specific ChipStatus register bits */ #define CST43239_SPROM_MASK 0x00000002 #define CST43239_SFLASH_MASK 0x00000004 #define CST43239_RES_INIT_MODE_SHIFT 7 #define CST43239_RES_INIT_MODE_MASK 0x000001f0 #define CST43239_CHIPMODE_SDIOD(cs) ((cs) & (1 << 15)) /* SDIO || gSPI */ #define CST43239_CHIPMODE_USB20D(cs) (~(cs) & (1 << 15)) /* USB || USBDA */ #define CST43239_CHIPMODE_SDIO(cs) (((cs) & (1 << 0)) == 0) /* SDIO */ #define CST43239_CHIPMODE_GSPI(cs) (((cs) & (1 << 0)) == (1 << 0)) /* gSPI */ /* 4324 resources */ /* 43242 use same PMU as 4324 */ #define RES4324_LPLDO_PU 0 #define RES4324_RESET_PULLDN_DIS 1 #define RES4324_PMU_BG_PU 2 #define RES4324_HSIC_LDO_PU 3 #define RES4324_CBUCK_LPOM_PU 4 #define RES4324_CBUCK_PFM_PU 5 #define RES4324_CLDO_PU 6 #define RES4324_LPLDO2_LVM 7 #define RES4324_LNLDO1_PU 8 #define RES4324_LNLDO2_PU 9 #define RES4324_LDO3P3_PU 10 #define RES4324_OTP_PU 11 #define RES4324_XTAL_PU 12 #define RES4324_BBPLL_PU 13 #define RES4324_LQ_AVAIL 14 #define RES4324_WL_CORE_READY 17 #define RES4324_ILP_REQ 18 #define RES4324_ALP_AVAIL 19 #define RES4324_PALDO_PU 20 #define RES4324_RADIO_PU 21 #define RES4324_SR_CLK_STABLE 22 #define RES4324_SR_SAVE_RESTORE 23 #define RES4324_SR_PHY_PWRSW 24 #define RES4324_SR_PHY_PIC 25 #define RES4324_SR_SUBCORE_PWRSW 26 #define RES4324_SR_SUBCORE_PIC 27 #define RES4324_SR_MEM_PM0 28 #define RES4324_HT_AVAIL 29 #define RES4324_MACPHY_CLKAVAIL 30 /* 4324 Chip specific ChipStatus register bits */ #define CST4324_SPROM_MASK 0x00000080 #define CST4324_SFLASH_MASK 0x00400000 #define CST4324_RES_INIT_MODE_SHIFT 10 #define CST4324_RES_INIT_MODE_MASK 0x00000c00 #define CST4324_CHIPMODE_MASK 0x7 #define CST4324_CHIPMODE_SDIOD(cs) ((~(cs)) & (1 << 2)) /* SDIO || gSPI */ #define CST4324_CHIPMODE_USB20D(cs) (((cs) & CST4324_CHIPMODE_MASK) == 0x6) /* USB || USBDA */ /* 43242 Chip specific ChipStatus register bits */ #define CST43242_SFLASH_MASK 0x00000008 /* 4331 resources */ #define RES4331_REGULATOR 0 #define RES4331_ILP_REQUEST 1 #define RES4331_XTAL_PU 2 #define RES4331_ALP_AVAIL 3 #define RES4331_SI_PLL_ON 4 #define RES4331_HT_SI_AVAIL 5 /* 4331 chip-specific ChipControl register bits */ #define CCTRL4331_BT_COEXIST (1<<0) /* 0 disable */ #define CCTRL4331_SECI (1<<1) /* 0 SECI is disabled (JATG functional) */ #define CCTRL4331_EXT_LNA_G (1<<2) /* 0 disable */ #define CCTRL4331_SPROM_GPIO13_15 (1<<3) /* sprom/gpio13-15 mux */ #define CCTRL4331_EXTPA_EN (1<<4) /* 0 ext pa disable, 1 ext pa enabled */ #define CCTRL4331_GPIOCLK_ON_SPROMCS (1<<5) /* set drive out GPIO_CLK on sprom_cs pin */ #define CCTRL4331_PCIE_MDIO_ON_SPROMCS (1<<6) /* use sprom_cs pin as PCIE mdio interface */ #define CCTRL4331_EXTPA_ON_GPIO2_5 (1<<7) /* aband extpa will be at gpio2/5 and sprom_dout */ #define CCTRL4331_OVR_PIPEAUXCLKEN (1<<8) /* override core control on pipe_AuxClkEnable */ #define CCTRL4331_OVR_PIPEAUXPWRDOWN (1<<9) /* override core control on pipe_AuxPowerDown */ #define CCTRL4331_PCIE_AUXCLKEN (1<<10) /* pcie_auxclkenable */ #define CCTRL4331_PCIE_PIPE_PLLDOWN (1<<11) /* pcie_pipe_pllpowerdown */ #define CCTRL4331_EXTPA_EN2 (1<<12) /* 0 ext pa disable, 1 ext pa enabled */ #define CCTRL4331_EXT_LNA_A (1<<13) /* 0 disable */ #define CCTRL4331_BT_SHD0_ON_GPIO4 (1<<16) /* enable bt_shd0 at gpio4 */ #define CCTRL4331_BT_SHD1_ON_GPIO5 (1<<17) /* enable bt_shd1 at gpio5 */ #define CCTRL4331_EXTPA_ANA_EN (1<<24) /* 0 ext pa disable, 1 ext pa enabled */ /* 4331 Chip specific ChipStatus register bits */ #define CST4331_XTAL_FREQ 0x00000001 /* crystal frequency 20/40Mhz */ #define CST4331_SPROM_OTP_SEL_MASK 0x00000006 #define CST4331_SPROM_OTP_SEL_SHIFT 1 #define CST4331_SPROM_PRESENT 0x00000002 #define CST4331_OTP_PRESENT 0x00000004 #define CST4331_LDO_RF 0x00000008 #define CST4331_LDO_PAR 0x00000010 /* 4315 resource */ #define RES4315_CBUCK_LPOM 1 /* 0x00000002 */ #define RES4315_CBUCK_BURST 2 /* 0x00000004 */ #define RES4315_CBUCK_PWM 3 /* 0x00000008 */ #define RES4315_CLDO_PU 4 /* 0x00000010 */ #define RES4315_PALDO_PU 5 /* 0x00000020 */ #define RES4315_ILP_REQUEST 6 /* 0x00000040 */ #define RES4315_LNLDO1_PU 9 /* 0x00000200 */ #define RES4315_OTP_PU 10 /* 0x00000400 */ #define RES4315_LNLDO2_PU 12 /* 0x00001000 */ #define RES4315_XTAL_PU 13 /* 0x00002000 */ #define RES4315_ALP_AVAIL 14 /* 0x00004000 */ #define RES4315_RX_PWRSW_PU 15 /* 0x00008000 */ #define RES4315_TX_PWRSW_PU 16 /* 0x00010000 */ #define RES4315_RFPLL_PWRSW_PU 17 /* 0x00020000 */ #define RES4315_LOGEN_PWRSW_PU 18 /* 0x00040000 */ #define RES4315_AFE_PWRSW_PU 19 /* 0x00080000 */ #define RES4315_BBPLL_PWRSW_PU 20 /* 0x00100000 */ #define RES4315_HT_AVAIL 21 /* 0x00200000 */ /* 4315 chip-specific ChipStatus register bits */ #define CST4315_SPROM_OTP_SEL_MASK 0x00000003 /* gpio [7:6], SDIO CIS selection */ #define CST4315_DEFCIS_SEL 0x00000000 /* use default CIS, OTP is powered up */ #define CST4315_SPROM_SEL 0x00000001 /* use SPROM, OTP is powered up */ #define CST4315_OTP_SEL 0x00000002 /* use OTP, OTP is powered up */ #define CST4315_OTP_PWRDN 0x00000003 /* use SPROM, OTP is powered down */ #define CST4315_SDIO_MODE 0x00000004 /* gpio [8], sdio/usb mode */ #define CST4315_RCAL_VALID 0x00000008 #define CST4315_RCAL_VALUE_MASK 0x000001f0 #define CST4315_RCAL_VALUE_SHIFT 4 #define CST4315_PALDO_EXTPNP 0x00000200 /* PALDO is configured with external PNP */ #define CST4315_CBUCK_MODE_MASK 0x00000c00 #define CST4315_CBUCK_MODE_BURST 0x00000400 #define CST4315_CBUCK_MODE_LPBURST 0x00000c00 /* 4319 resources */ #define RES4319_CBUCK_LPOM 1 /* 0x00000002 */ #define RES4319_CBUCK_BURST 2 /* 0x00000004 */ #define RES4319_CBUCK_PWM 3 /* 0x00000008 */ #define RES4319_CLDO_PU 4 /* 0x00000010 */ #define RES4319_PALDO_PU 5 /* 0x00000020 */ #define RES4319_ILP_REQUEST 6 /* 0x00000040 */ #define RES4319_LNLDO1_PU 9 /* 0x00000200 */ #define RES4319_OTP_PU 10 /* 0x00000400 */ #define RES4319_LNLDO2_PU 12 /* 0x00001000 */ #define RES4319_XTAL_PU 13 /* 0x00002000 */ #define RES4319_ALP_AVAIL 14 /* 0x00004000 */ #define RES4319_RX_PWRSW_PU 15 /* 0x00008000 */ #define RES4319_TX_PWRSW_PU 16 /* 0x00010000 */ #define RES4319_RFPLL_PWRSW_PU 17 /* 0x00020000 */ #define RES4319_LOGEN_PWRSW_PU 18 /* 0x00040000 */ #define RES4319_AFE_PWRSW_PU 19 /* 0x00080000 */ #define RES4319_BBPLL_PWRSW_PU 20 /* 0x00100000 */ #define RES4319_HT_AVAIL 21 /* 0x00200000 */ /* 4319 chip-specific ChipStatus register bits */ #define CST4319_SPI_CPULESSUSB 0x00000001 #define CST4319_SPI_CLK_POL 0x00000002 #define CST4319_SPI_CLK_PH 0x00000008 #define CST4319_SPROM_OTP_SEL_MASK 0x000000c0 /* gpio [7:6], SDIO CIS selection */ #define CST4319_SPROM_OTP_SEL_SHIFT 6 #define CST4319_DEFCIS_SEL 0x00000000 /* use default CIS, OTP is powered up */ #define CST4319_SPROM_SEL 0x00000040 /* use SPROM, OTP is powered up */ #define CST4319_OTP_SEL 0x00000080 /* use OTP, OTP is powered up */ #define CST4319_OTP_PWRDN 0x000000c0 /* use SPROM, OTP is powered down */ #define CST4319_SDIO_USB_MODE 0x00000100 /* gpio [8], sdio/usb mode */ #define CST4319_REMAP_SEL_MASK 0x00000600 #define CST4319_ILPDIV_EN 0x00000800 #define CST4319_XTAL_PD_POL 0x00001000 #define CST4319_LPO_SEL 0x00002000 #define CST4319_RES_INIT_MODE 0x0000c000 #define CST4319_PALDO_EXTPNP 0x00010000 /* PALDO is configured with external PNP */ #define CST4319_CBUCK_MODE_MASK 0x00060000 #define CST4319_CBUCK_MODE_BURST 0x00020000 #define CST4319_CBUCK_MODE_LPBURST 0x00060000 #define CST4319_RCAL_VALID 0x01000000 #define CST4319_RCAL_VALUE_MASK 0x3e000000 #define CST4319_RCAL_VALUE_SHIFT 25 #define PMU1_PLL0_CHIPCTL0 0 #define PMU1_PLL0_CHIPCTL1 1 #define PMU1_PLL0_CHIPCTL2 2 #define CCTL_4319USB_XTAL_SEL_MASK 0x00180000 #define CCTL_4319USB_XTAL_SEL_SHIFT 19 #define CCTL_4319USB_48MHZ_PLL_SEL 1 #define CCTL_4319USB_24MHZ_PLL_SEL 2 /* PMU resources for 4336 */ #define RES4336_CBUCK_LPOM 0 #define RES4336_CBUCK_BURST 1 #define RES4336_CBUCK_LP_PWM 2 #define RES4336_CBUCK_PWM 3 #define RES4336_CLDO_PU 4 #define RES4336_DIS_INT_RESET_PD 5 #define RES4336_ILP_REQUEST 6 #define RES4336_LNLDO_PU 7 #define RES4336_LDO3P3_PU 8 #define RES4336_OTP_PU 9 #define RES4336_XTAL_PU 10 #define RES4336_ALP_AVAIL 11 #define RES4336_RADIO_PU 12 #define RES4336_BG_PU 13 #define RES4336_VREG1p4_PU_PU 14 #define RES4336_AFE_PWRSW_PU 15 #define RES4336_RX_PWRSW_PU 16 #define RES4336_TX_PWRSW_PU 17 #define RES4336_BB_PWRSW_PU 18 #define RES4336_SYNTH_PWRSW_PU 19 #define RES4336_MISC_PWRSW_PU 20 #define RES4336_LOGEN_PWRSW_PU 21 #define RES4336_BBPLL_PWRSW_PU 22 #define RES4336_MACPHY_CLKAVAIL 23 #define RES4336_HT_AVAIL 24 #define RES4336_RSVD 25 /* 4336 chip-specific ChipStatus register bits */ #define CST4336_SPI_MODE_MASK 0x00000001 #define CST4336_SPROM_PRESENT 0x00000002 #define CST4336_OTP_PRESENT 0x00000004 #define CST4336_ARMREMAP_0 0x00000008 #define CST4336_ILPDIV_EN_MASK 0x00000010 #define CST4336_ILPDIV_EN_SHIFT 4 #define CST4336_XTAL_PD_POL_MASK 0x00000020 #define CST4336_XTAL_PD_POL_SHIFT 5 #define CST4336_LPO_SEL_MASK 0x00000040 #define CST4336_LPO_SEL_SHIFT 6 #define CST4336_RES_INIT_MODE_MASK 0x00000180 #define CST4336_RES_INIT_MODE_SHIFT 7 #define CST4336_CBUCK_MODE_MASK 0x00000600 #define CST4336_CBUCK_MODE_SHIFT 9 /* 4336 Chip specific PMU ChipControl register bits */ #define PCTL_4336_SERIAL_ENAB (1 << 24) /* 4330 resources */ #define RES4330_CBUCK_LPOM 0 #define RES4330_CBUCK_BURST 1 #define RES4330_CBUCK_LP_PWM 2 #define RES4330_CBUCK_PWM 3 #define RES4330_CLDO_PU 4 #define RES4330_DIS_INT_RESET_PD 5 #define RES4330_ILP_REQUEST 6 #define RES4330_LNLDO_PU 7 #define RES4330_LDO3P3_PU 8 #define RES4330_OTP_PU 9 #define RES4330_XTAL_PU 10 #define RES4330_ALP_AVAIL 11 #define RES4330_RADIO_PU 12 #define RES4330_BG_PU 13 #define RES4330_VREG1p4_PU_PU 14 #define RES4330_AFE_PWRSW_PU 15 #define RES4330_RX_PWRSW_PU 16 #define RES4330_TX_PWRSW_PU 17 #define RES4330_BB_PWRSW_PU 18 #define RES4330_SYNTH_PWRSW_PU 19 #define RES4330_MISC_PWRSW_PU 20 #define RES4330_LOGEN_PWRSW_PU 21 #define RES4330_BBPLL_PWRSW_PU 22 #define RES4330_MACPHY_CLKAVAIL 23 #define RES4330_HT_AVAIL 24 #define RES4330_5gRX_PWRSW_PU 25 #define RES4330_5gTX_PWRSW_PU 26 #define RES4330_5g_LOGEN_PWRSW_PU 27 /* 4330 chip-specific ChipStatus register bits */ #define CST4330_CHIPMODE_SDIOD(cs) (((cs) & 0x7) < 6) /* SDIO || gSPI */ #define CST4330_CHIPMODE_USB20D(cs) (((cs) & 0x7) >= 6) /* USB || USBDA */ #define CST4330_CHIPMODE_SDIO(cs) (((cs) & 0x4) == 0) /* SDIO */ #define CST4330_CHIPMODE_GSPI(cs) (((cs) & 0x6) == 4) /* gSPI */ #define CST4330_CHIPMODE_USB(cs) (((cs) & 0x7) == 6) /* USB packet-oriented */ #define CST4330_CHIPMODE_USBDA(cs) (((cs) & 0x7) == 7) /* USB Direct Access */ #define CST4330_OTP_PRESENT 0x00000010 #define CST4330_LPO_AUTODET_EN 0x00000020 #define CST4330_ARMREMAP_0 0x00000040 #define CST4330_SPROM_PRESENT 0x00000080 /* takes priority over OTP if both set */ #define CST4330_ILPDIV_EN 0x00000100 #define CST4330_LPO_SEL 0x00000200 #define CST4330_RES_INIT_MODE_SHIFT 10 #define CST4330_RES_INIT_MODE_MASK 0x00000c00 #define CST4330_CBUCK_MODE_SHIFT 12 #define CST4330_CBUCK_MODE_MASK 0x00003000 #define CST4330_CBUCK_POWER_OK 0x00004000 #define CST4330_BB_PLL_LOCKED 0x00008000 #define SOCDEVRAM_BP_ADDR 0x1E000000 #define SOCDEVRAM_ARM_ADDR 0x00800000 /* 4330 Chip specific PMU ChipControl register bits */ #define PCTL_4330_SERIAL_ENAB (1 << 24) /* 4330 Chip specific ChipControl register bits */ #define CCTRL_4330_GPIO_SEL 0x00000001 /* 1=select GPIOs to be muxed out */ #define CCTRL_4330_ERCX_SEL 0x00000002 /* 1=select ERCX BT coex to be muxed out */ #define CCTRL_4330_SDIO_HOST_WAKE 0x00000004 /* SDIO: 1=configure GPIO0 for host wake */ #define CCTRL_4330_JTAG_DISABLE 0x00000008 /* 1=disable JTAG interface on mux'd pins */ #define PMU_VREG0_ADDR 0 #define PMU_VREG0_DISABLE_PULLD_BT_SHIFT 2 #define PMU_VREG0_DISABLE_PULLD_WL_SHIFT 3 #define PMU_VREG4_ADDR 4 #define PMU_VREG4_CLDO_PWM_SHIFT 4 #define PMU_VREG4_CLDO_PWM_MASK 0x7 #define PMU_VREG4_LPLDO1_SHIFT 15 #define PMU_VREG4_LPLDO1_MASK 0x7 #define PMU_VREG4_LPLDO1_1p20V 0 #define PMU_VREG4_LPLDO1_1p15V 1 #define PMU_VREG4_LPLDO1_1p10V 2 #define PMU_VREG4_LPLDO1_1p25V 3 #define PMU_VREG4_LPLDO1_1p05V 4 #define PMU_VREG4_LPLDO1_1p00V 5 #define PMU_VREG4_LPLDO1_0p95V 6 #define PMU_VREG4_LPLDO1_0p90V 7 #define PMU_VREG4_LPLDO2_LVM_SHIFT 18 #define PMU_VREG4_LPLDO2_LVM_MASK 0x7 #define PMU_VREG4_LPLDO2_HVM_SHIFT 21 #define PMU_VREG4_LPLDO2_HVM_MASK 0x7 #define PMU_VREG4_LPLDO2_LVM_HVM_MASK 0x3f #define PMU_VREG4_LPLDO2_1p00V 0 #define PMU_VREG4_LPLDO2_1p15V 1 #define PMU_VREG4_LPLDO2_1p20V 2 #define PMU_VREG4_LPLDO2_1p10V 3 #define PMU_VREG4_LPLDO2_0p90V 4 /* 4 - 7 is 0.90V */ #define PMU_VREG4_HSICLDO_BYPASS_SHIFT 27 #define PMU_VREG4_HSICLDO_BYPASS_MASK 0x1 #define PMU_VREG5_ADDR 5 #define PMU_VREG5_HSICAVDD_PD_SHIFT 6 #define PMU_VREG5_HSICAVDD_PD_MASK 0x1 #define PMU_VREG5_HSICDVDD_PD_SHIFT 11 #define PMU_VREG5_HSICDVDD_PD_MASK 0x1 /* 4334 resources */ #define RES4334_LPLDO_PU 0 #define RES4334_RESET_PULLDN_DIS 1 #define RES4334_PMU_BG_PU 2 #define RES4334_HSIC_LDO_PU 3 #define RES4334_CBUCK_LPOM_PU 4 #define RES4334_CBUCK_PFM_PU 5 #define RES4334_CLDO_PU 6 #define RES4334_LPLDO2_LVM 7 #define RES4334_LNLDO_PU 8 #define RES4334_LDO3P3_PU 9 #define RES4334_OTP_PU 10 #define RES4334_XTAL_PU 11 #define RES4334_WL_PWRSW_PU 12 #define RES4334_LQ_AVAIL 13 #define RES4334_LOGIC_RET 14 #define RES4334_MEM_SLEEP 15 #define RES4334_MACPHY_RET 16 #define RES4334_WL_CORE_READY 17 #define RES4334_ILP_REQ 18 #define RES4334_ALP_AVAIL 19 #define RES4334_MISC_PWRSW_PU 20 #define RES4334_SYNTH_PWRSW_PU 21 #define RES4334_RX_PWRSW_PU 22 #define RES4334_RADIO_PU 23 #define RES4334_WL_PMU_PU 24 #define RES4334_VCO_LDO_PU 25 #define RES4334_AFE_LDO_PU 26 #define RES4334_RX_LDO_PU 27 #define RES4334_TX_LDO_PU 28 #define RES4334_HT_AVAIL 29 #define RES4334_MACPHY_CLK_AVAIL 30 /* 4334 chip-specific ChipStatus register bits */ #define CST4334_CHIPMODE_MASK 7 #define CST4334_SDIO_MODE 0x00000000 #define CST4334_SPI_MODE 0x00000004 #define CST4334_HSIC_MODE 0x00000006 #define CST4334_BLUSB_MODE 0x00000007 #define CST4334_CHIPMODE_HSIC(cs) (((cs) & CST4334_CHIPMODE_MASK) == CST4334_HSIC_MODE) #define CST4334_OTP_PRESENT 0x00000010 #define CST4334_LPO_AUTODET_EN 0x00000020 #define CST4334_ARMREMAP_0 0x00000040 #define CST4334_SPROM_PRESENT 0x00000080 #define CST4334_ILPDIV_EN_MASK 0x00000100 #define CST4334_ILPDIV_EN_SHIFT 8 #define CST4334_LPO_SEL_MASK 0x00000200 #define CST4334_LPO_SEL_SHIFT 9 #define CST4334_RES_INIT_MODE_MASK 0x00000C00 #define CST4334_RES_INIT_MODE_SHIFT 10 /* 4334 Chip specific PMU ChipControl register bits */ #define PCTL_4334_GPIO3_ENAB (1 << 3) /* 4334 Chip control */ #define CCTRL4334_PMU_WAKEUP_GPIO1 (1 << 0) #define CCTRL4334_PMU_WAKEUP_HSIC (1 << 1) #define CCTRL4334_PMU_WAKEUP_AOS (1 << 2) #define CCTRL4334_HSIC_WAKE_MODE (1 << 3) #define CCTRL4334_HSIC_INBAND_GPIO1 (1 << 4) #define CCTRL4334_HSIC_LDO_PU (1 << 23) /* 4334 Chip control 3 */ #define CCTRL4334_BLOCK_EXTRNL_WAKE (1 << 4) #define CCTRL4334_SAVERESTORE_FIX (1 << 5) /* 43341 Chip control 3 */ #define CCTRL43341_BLOCK_EXTRNL_WAKE (1 << 13) #define CCTRL43341_SAVERESTORE_FIX (1 << 14) #define CCTRL43341_BT_ISO_SEL (1 << 16) /* 4334 Chip specific ChipControl1 register bits */ #define CCTRL1_4334_GPIO_SEL (1 << 0) /* 1=select GPIOs to be muxed out */ #define CCTRL1_4334_ERCX_SEL (1 << 1) /* 1=select ERCX BT coex to be muxed out */ #define CCTRL1_4334_SDIO_HOST_WAKE (1 << 2) /* SDIO: 1=configure GPIO0 for host wake */ #define CCTRL1_4334_JTAG_DISABLE (1 << 3) /* 1=disable JTAG interface on mux'd pins */ #define CCTRL1_4334_UART_ON_4_5 (1 << 28) /* 1=UART_TX/UART_RX muxed on GPIO_4/5 (4334B0/1) */ /* 4324 Chip specific ChipControl1 register bits */ #define CCTRL1_4324_GPIO_SEL (1 << 0) /* 1=select GPIOs to be muxed out */ #define CCTRL1_4324_SDIO_HOST_WAKE (1 << 2) /* SDIO: 1=configure GPIO0 for host wake */ /* 43143 chip-specific ChipStatus register bits based on Confluence documentation */ /* register contains strap values sampled during POR */ #define CST43143_REMAP_TO_ROM (3 << 0) /* 00=Boot SRAM, 01=Boot ROM, 10=Boot SFLASH */ #define CST43143_SDIO_EN (1 << 2) /* 0 = USB Enab, SDIO pins are GPIO or I2S */ #define CST43143_SDIO_ISO (1 << 3) /* 1 = SDIO isolated */ #define CST43143_USB_CPU_LESS (1 << 4) /* 1 = CPULess mode Enabled */ #define CST43143_CBUCK_MODE (3 << 6) /* Indicates what controller mode CBUCK is in */ #define CST43143_POK_CBUCK (1 << 8) /* 1 = 1.2V CBUCK voltage ready */ #define CST43143_PMU_OVRSPIKE (1 << 9) #define CST43143_PMU_OVRTEMP (0xF << 10) #define CST43143_SR_FLL_CAL_DONE (1 << 14) #define CST43143_USB_PLL_LOCKDET (1 << 15) #define CST43143_PMU_PLL_LOCKDET (1 << 16) #define CST43143_CHIPMODE_SDIOD(cs) (((cs) & CST43143_SDIO_EN) != 0) /* SDIO */ /* 43143 Chip specific ChipControl register bits */ /* 00: SECI is disabled (JATG functional), 01: 2 wire, 10: 4 wire */ #define CCTRL_43143_SECI (1<<0) #define CCTRL_43143_BT_LEGACY (1<<1) #define CCTRL_43143_I2S_MODE (1<<2) /* 0: SDIO enabled */ #define CCTRL_43143_I2S_MASTER (1<<3) /* 0: I2S MCLK input disabled */ #define CCTRL_43143_I2S_FULL (1<<4) /* 0: I2S SDIN and SPDIF_TX inputs disabled */ #define CCTRL_43143_GSIO (1<<5) /* 0: sFlash enabled */ #define CCTRL_43143_RF_SWCTRL_MASK (7<<6) /* 0: disabled */ #define CCTRL_43143_RF_SWCTRL_0 (1<<6) #define CCTRL_43143_RF_SWCTRL_1 (2<<6) #define CCTRL_43143_RF_SWCTRL_2 (4<<6) #define CCTRL_43143_RF_XSWCTRL (1<<9) /* 0: UART enabled */ #define CCTRL_43143_HOST_WAKE0 (1<<11) /* 1: SDIO separate interrupt output from GPIO4 */ #define CCTRL_43143_HOST_WAKE1 (1<<12) /* 1: SDIO separate interrupt output from GPIO16 */ /* 43143 resources, based on pmu_params.xls V1.19 */ #define RES43143_EXT_SWITCHER_PWM 0 /* 0x00001 */ #define RES43143_XTAL_PU 1 /* 0x00002 */ #define RES43143_ILP_REQUEST 2 /* 0x00004 */ #define RES43143_ALP_AVAIL 3 /* 0x00008 */ #define RES43143_WL_CORE_READY 4 /* 0x00010 */ #define RES43143_BBPLL_PWRSW_PU 5 /* 0x00020 */ #define RES43143_HT_AVAIL 6 /* 0x00040 */ #define RES43143_RADIO_PU 7 /* 0x00080 */ #define RES43143_MACPHY_CLK_AVAIL 8 /* 0x00100 */ #define RES43143_OTP_PU 9 /* 0x00200 */ #define RES43143_LQ_AVAIL 10 /* 0x00400 */ #define PMU43143_XTAL_CORE_SIZE_MASK 0x3F /* 4313 resources */ #define RES4313_BB_PU_RSRC 0 #define RES4313_ILP_REQ_RSRC 1 #define RES4313_XTAL_PU_RSRC 2 #define RES4313_ALP_AVAIL_RSRC 3 #define RES4313_RADIO_PU_RSRC 4 #define RES4313_BG_PU_RSRC 5 #define RES4313_VREG1P4_PU_RSRC 6 #define RES4313_AFE_PWRSW_RSRC 7 #define RES4313_RX_PWRSW_RSRC 8 #define RES4313_TX_PWRSW_RSRC 9 #define RES4313_BB_PWRSW_RSRC 10 #define RES4313_SYNTH_PWRSW_RSRC 11 #define RES4313_MISC_PWRSW_RSRC 12 #define RES4313_BB_PLL_PWRSW_RSRC 13 #define RES4313_HT_AVAIL_RSRC 14 #define RES4313_MACPHY_CLK_AVAIL_RSRC 15 /* 4313 chip-specific ChipStatus register bits */ #define CST4313_SPROM_PRESENT 1 #define CST4313_OTP_PRESENT 2 #define CST4313_SPROM_OTP_SEL_MASK 0x00000002 #define CST4313_SPROM_OTP_SEL_SHIFT 0 /* 4313 Chip specific ChipControl register bits */ #define CCTRL_4313_12MA_LED_DRIVE 0x00000007 /* 12 mA drive strengh for later 4313 */ /* PMU respources for 4314 */ #define RES4314_LPLDO_PU 0 #define RES4314_PMU_SLEEP_DIS 1 #define RES4314_PMU_BG_PU 2 #define RES4314_CBUCK_LPOM_PU 3 #define RES4314_CBUCK_PFM_PU 4 #define RES4314_CLDO_PU 5 #define RES4314_LPLDO2_LVM 6 #define RES4314_WL_PMU_PU 7 #define RES4314_LNLDO_PU 8 #define RES4314_LDO3P3_PU 9 #define RES4314_OTP_PU 10 #define RES4314_XTAL_PU 11 #define RES4314_WL_PWRSW_PU 12 #define RES4314_LQ_AVAIL 13 #define RES4314_LOGIC_RET 14 #define RES4314_MEM_SLEEP 15 #define RES4314_MACPHY_RET 16 #define RES4314_WL_CORE_READY 17 #define RES4314_ILP_REQ 18 #define RES4314_ALP_AVAIL 19 #define RES4314_MISC_PWRSW_PU 20 #define RES4314_SYNTH_PWRSW_PU 21 #define RES4314_RX_PWRSW_PU 22 #define RES4314_RADIO_PU 23 #define RES4314_VCO_LDO_PU 24 #define RES4314_AFE_LDO_PU 25 #define RES4314_RX_LDO_PU 26 #define RES4314_TX_LDO_PU 27 #define RES4314_HT_AVAIL 28 #define RES4314_MACPHY_CLK_AVAIL 29 /* 4314 chip-specific ChipStatus register bits */ #define CST4314_OTP_ENABLED 0x00200000 /* 43228 resources */ #define RES43228_NOT_USED 0 #define RES43228_ILP_REQUEST 1 #define RES43228_XTAL_PU 2 #define RES43228_ALP_AVAIL 3 #define RES43228_PLL_EN 4 #define RES43228_HT_PHY_AVAIL 5 /* 43228 chipstatus reg bits */ #define CST43228_ILP_DIV_EN 0x1 #define CST43228_OTP_PRESENT 0x2 #define CST43228_SERDES_REFCLK_PADSEL 0x4 #define CST43228_SDIO_MODE 0x8 #define CST43228_SDIO_OTP_PRESENT 0x10 #define CST43228_SDIO_RESET 0x20 /* 4706 chipstatus reg bits */ #define CST4706_PKG_OPTION (1<<0) /* 0: full-featured package 1: low-cost package */ #define CST4706_SFLASH_PRESENT (1<<1) /* 0: parallel, 1: serial flash is present */ #define CST4706_SFLASH_TYPE (1<<2) /* 0: 8b-p/ST-s flash, 1: 16b-p/Atmal-s flash */ #define CST4706_MIPS_BENDIAN (1<<3) /* 0: little, 1: big endian */ #define CST4706_PCIE1_DISABLE (1<<5) /* PCIE1 enable strap pin */ /* 4706 flashstrconfig reg bits */ #define FLSTRCF4706_MASK 0x000000ff #define FLSTRCF4706_SF1 0x00000001 /* 2nd serial flash present */ #define FLSTRCF4706_PF1 0x00000002 /* 2nd parallel flash present */ #define FLSTRCF4706_SF1_TYPE 0x00000004 /* 2nd serial flash type : 0 : ST, 1 : Atmel */ #define FLSTRCF4706_NF1 0x00000008 /* 2nd NAND flash present */ #define FLSTRCF4706_1ST_MADDR_SEG_MASK 0x000000f0 /* Valid value mask */ #define FLSTRCF4706_1ST_MADDR_SEG_4MB 0x00000010 /* 4MB */ #define FLSTRCF4706_1ST_MADDR_SEG_8MB 0x00000020 /* 8MB */ #define FLSTRCF4706_1ST_MADDR_SEG_16MB 0x00000030 /* 16MB */ #define FLSTRCF4706_1ST_MADDR_SEG_32MB 0x00000040 /* 32MB */ #define FLSTRCF4706_1ST_MADDR_SEG_64MB 0x00000050 /* 64MB */ #define FLSTRCF4706_1ST_MADDR_SEG_128MB 0x00000060 /* 128MB */ #define FLSTRCF4706_1ST_MADDR_SEG_256MB 0x00000070 /* 256MB */ /* 4360 Chip specific ChipControl register bits */ #define CCTRL4360_I2C_MODE (1 << 0) #define CCTRL4360_UART_MODE (1 << 1) #define CCTRL4360_SECI_MODE (1 << 2) #define CCTRL4360_BTSWCTRL_MODE (1 << 3) #define CCTRL4360_DISCRETE_FEMCTRL_MODE (1 << 4) #define CCTRL4360_DIGITAL_PACTRL_MODE (1 << 5) #define CCTRL4360_BTSWCTRL_AND_DIGPA_PRESENT (1 << 6) #define CCTRL4360_EXTRA_GPIO_MODE (1 << 7) #define CCTRL4360_EXTRA_FEMCTRL_MODE (1 << 8) #define CCTRL4360_BT_LGCY_MODE (1 << 9) #define CCTRL4360_CORE2FEMCTRL4_ON (1 << 21) #define CCTRL4360_SECI_ON_GPIO01 (1 << 24) /* 4360 PMU resources and chip status bits */ #define RES4360_REGULATOR 0 #define RES4360_ILP_AVAIL 1 #define RES4360_ILP_REQ 2 #define RES4360_XTAL_LDO_PU 3 #define RES4360_XTAL_PU 4 #define RES4360_ALP_AVAIL 5 #define RES4360_BBPLLPWRSW_PU 6 #define RES4360_HT_AVAIL 7 #define RES4360_OTP_PU 8 #define CST4360_XTAL_40MZ 0x00000001 #define CST4360_SFLASH 0x00000002 #define CST4360_SPROM_PRESENT 0x00000004 #define CST4360_SFLASH_TYPE 0x00000004 #define CST4360_OTP_ENABLED 0x00000008 #define CST4360_REMAP_ROM 0x00000010 #define CST4360_RSRC_INIT_MODE_MASK 0x00000060 #define CST4360_RSRC_INIT_MODE_SHIFT 5 #define CST4360_ILP_DIVEN 0x00000080 #define CST4360_MODE_USB 0x00000100 #define CST4360_SPROM_SIZE_MASK 0x00000600 #define CST4360_SPROM_SIZE_SHIFT 9 #define CST4360_BBPLL_LOCK 0x00000800 #define CST4360_AVBBPLL_LOCK 0x00001000 #define CST4360_USBBBPLL_LOCK 0x00002000 #define CCTRL_4360_UART_SEL 0x2 /* defines to detect active host interface in use */ #define CHIP_HOSTIF_PCIEMODE 0x1 #define CHIP_HOSTIF_USBMODE 0x2 #define CHIP_HOSTIF_SDIOMODE 0x4 #define CHIP_HOSTIF_PCIE(sih) (si_chip_hostif(sih) == CHIP_HOSTIF_PCIEMODE) #define CHIP_HOSTIF_SDIO(sih) (si_chip_hostif(sih) == CHIP_HOSTIF_SDIOMODE) /* 4335 resources */ #define RES4335_LPLDO_PO 0 #define RES4335_PMU_BG_PU 1 #define RES4335_PMU_SLEEP 2 #define RES4335_RSVD_3 3 #define RES4335_CBUCK_LPOM_PU 4 #define RES4335_CBUCK_PFM_PU 5 #define RES4335_RSVD_6 6 #define RES4335_RSVD_7 7 #define RES4335_LNLDO_PU 8 #define RES4335_XTALLDO_PU 9 #define RES4335_LDO3P3_PU 10 #define RES4335_OTP_PU 11 #define RES4335_XTAL_PU 12 #define RES4335_SR_CLK_START 13 #define RES4335_LQ_AVAIL 14 #define RES4335_LQ_START 15 #define RES4335_RSVD_16 16 #define RES4335_WL_CORE_RDY 17 #define RES4335_ILP_REQ 18 #define RES4335_ALP_AVAIL 19 #define RES4335_MINI_PMU 20 #define RES4335_RADIO_PU 21 #define RES4335_SR_CLK_STABLE 22 #define RES4335_SR_SAVE_RESTORE 23 #define RES4335_SR_PHY_PWRSW 24 #define RES4335_SR_VDDM_PWRSW 25 #define RES4335_SR_SUBCORE_PWRSW 26 #define RES4335_SR_SLEEP 27 #define RES4335_HT_START 28 #define RES4335_HT_AVAIL 29 #define RES4335_MACPHY_CLKAVAIL 30 /* 4335 Chip specific ChipStatus register bits */ #define CST4335_SPROM_MASK 0x00000020 #define CST4335_SFLASH_MASK 0x00000040 #define CST4335_RES_INIT_MODE_SHIFT 7 #define CST4335_RES_INIT_MODE_MASK 0x00000180 #define CST4335_CHIPMODE_MASK 0xF #define CST4335_CHIPMODE_SDIOD(cs) (((cs) & (1 << 0)) != 0) /* SDIO */ #define CST4335_CHIPMODE_GSPI(cs) (((cs) & (1 << 1)) != 0) /* gSPI */ #define CST4335_CHIPMODE_USB20D(cs) (((cs) & (1 << 2)) != 0) /* USB || USBDA */ #define CST4335_CHIPMODE_PCIE(cs) (((cs) & (1 << 3)) != 0) /* PCIE */ /* 4335 Chip specific ChipControl1 register bits */ #define CCTRL1_4335_GPIO_SEL (1 << 0) /* 1=select GPIOs to be muxed out */ #define CCTRL1_4335_SDIO_HOST_WAKE (1 << 2) /* SDIO: 1=configure GPIO0 for host wake */ #define CR4_4335_RAM_BASE (0x180000) #define PATCHTBL_SIZE (0x800) #define CR4_4350_RAM_BASE (0x180000) #define CR4_4360_RAM_BASE (0x0) /* 4335 chip OTP present & OTP select bits. */ #define SPROM4335_OTP_SELECT 0x00000010 #define SPROM4335_OTP_PRESENT 0x00000020 /* 4335 GCI specific bits. */ #define CC4335_GCI_STRAP_OVERRIDE_SFLASH_PRESENT (1 << 24) #define CC4335_GCI_STRAP_OVERRIDE_SFLASH_TYPE 25 #define CC4335_GCI_FUNC_SEL_PAD_SDIO 0x00707770 /* SFLASH clkdev specific bits. */ #define CC4335_SFLASH_CLKDIV_MASK 0x1F000000 #define CC4335_SFLASH_CLKDIV_SHIFT 25 /* 4335 OTP bits for SFLASH. */ #define CC4335_SROM_OTP_SFLASH 40 #define CC4335_SROM_OTP_SFLASH_PRESENT 0x1 #define CC4335_SROM_OTP_SFLASH_TYPE 0x2 #define CC4335_SROM_OTP_SFLASH_CLKDIV_MASK 0x003C #define CC4335_SROM_OTP_SFLASH_CLKDIV_SHIFT 2 /* 4335 resources--END */ /* 4350 Chipcommon ChipStatus bits */ #define CST4350_SDIO_MODE 0x00000001 #define CST4350_HSIC20D_MODE 0x00000002 #define CST4350_BP_ON_HSIC_CLK 0x00000004 #define CST4350_PCIE_MODE 0x00000008 #define CST4350_USB20D_MODE 0x00000010 #define CST4350_USB30D_MODE 0x00000020 #define CST4350_SPROM_PRESENT 0x00000040 #define CST4350_RSRC_INIT_MODE_0 0x00000080 #define CST4350_RSRC_INIT_MODE_1 0x00000100 #define CST4350_SEL0_SDIO 0x00000200 #define CST4350_SEL1_SDIO 0x00000400 #define CST4350_SDIO_PAD_MODE 0x00000800 #define CST4350_BBPLL_LOCKED 0x00001000 #define CST4350_USBPLL_LOCKED 0x00002000 #define CST4350_LINE_STATE 0x0000C000 #define CST4350_SERDES_PIPE_PLLLOCK 0x00010000 #define CST4350_BT_READY 0x00020000 #define CST4350_SFLASH_PRESENT 0x00040000 #define CST4350_CPULESS_ENABLE 0x00080000 #define CST4350_STRAP_HOST_IFC_1 0x00100000 #define CST4350_STRAP_HOST_IFC_2 0x00200000 #define CST4350_STRAP_HOST_IFC_3 0x00400000 #define CST4350_RAW_SPROM_PRESENT 0x00800000 #define CST4350_APP_CLK_SWITCH_SEL_RDBACK 0x01000000 #define CST4350_RAW_RSRC_INIT_MODE_0 0x02000000 #define CST4350_SDIO_PAD_VDDIO 0x04000000 #define CST4350_GSPI_MODE 0x08000000 #define CST4350_PACKAGE_OPTION 0xF0000000 /* strap_host_ifc strap value */ #define CST4350_HOST_IFC_MASK 0x00700000 #define CST4350_HOST_IFC_SHIFT 20 /* host_ifc raw mode */ #define CST4350_IFC_MODE_SDIOD 0x0 #define CST4350_IFC_MODE_HSIC20D 0x1 #define CST4350_IFC_MODE_HSIC30D 0x2 #define CST4350_IFC_MODE_PCIE 0x3 #define CST4350_IFC_MODE_USB20D 0x4 #define CST4350_IFC_MODE_USB30D 0x5 #define CST4350_IFC_MODE_USB30D_WL 0x6 #define CST4350_IFC_MODE_USB30D_BT 0x7 #define CST4350_IFC_MODE(cs) ((cs & CST4350_HOST_IFC_MASK) >> CST4350_HOST_IFC_SHIFT) #define CST4350_CHIPMODE_SDIOD(cs) (CST4350_IFC_MODE(cs) == (CST4350_IFC_MODE_SDIOD)) #define CST4350_CHIPMODE_USB20D(cs) ((CST4350_IFC_MODE(cs)) == (CST4350_IFC_MODE_USB20D)) #define CST4350_CHIPMODE_HSIC20D(cs) (CST4350_IFC_MODE(cs) == (CST4350_IFC_MODE_HSIC20D)) #define CST4350_CHIPMODE_HSIC30D(cs) (CST4350_IFC_MODE(cs) == (CST4350_IFC_MODE_HSIC30D)) #define CST4350_CHIPMODE_USB30D(cs) (CST4350_IFC_MODE(cs) == (CST4350_IFC_MODE_USB30D)) #define CST4350_CHIPMODE_USB30D_WL(cs) (CST4350_IFC_MODE(cs) == (CST4350_IFC_MODE_USB30D_WL)) #define CST4350_CHIPMODE_PCIE(cs) (CST4350_IFC_MODE(cs) == (CST4350_IFC_MODE_PCIE)) /* 4350 PMU resources */ #define RES4350_LPLDO_PU 0 #define RES4350_PMU_BG_PU 1 #define RES4350_PMU_SLEEP 2 #define RES4350_RSVD_3 3 #define RES4350_CBUCK_LPOM_PU 4 #define RES4350_CBUCK_PFM_PU 5 #define RES4350_COLD_START_WAIT 6 #define RES4350_RSVD_7 7 #define RES4350_LNLDO_PU 8 #define RES4350_XTALLDO_PU 9 #define RES4350_LDO3P3_PU 10 #define RES4350_OTP_PU 11 #define RES4350_XTAL_PU 12 #define RES4350_SR_CLK_START 13 #define RES4350_LQ_AVAIL 14 #define RES4350_LQ_START 15 #define RES4350_RSVD_16 16 #define RES4350_WL_CORE_RDY 17 #define RES4350_ILP_REQ 18 #define RES4350_ALP_AVAIL 19 #define RES4350_MINI_PMU 20 #define RES4350_RADIO_PU 21 #define RES4350_SR_CLK_STABLE 22 #define RES4350_SR_SAVE_RESTORE 23 #define RES4350_SR_PHY_PWRSW 24 #define RES4350_SR_VDDM_PWRSW 25 #define RES4350_SR_SUBCORE_PWRSW 26 #define RES4350_SR_SLEEP 27 #define RES4350_HT_START 28 #define RES4350_HT_AVAIL 29 #define RES4350_MACPHY_CLKAVAIL 30 #define MUXENAB4350_UART_MASK (0x0000000f) /* 4350 GCI function sel values */ #define CC4350_FNSEL_HWDEF (0) #define CC4350_FNSEL_SAMEASPIN (1) #define CC4350_FNSEL_UART (2) #define CC4350_FNSEL_SFLASH (3) #define CC4350_FNSEL_SPROM (4) #define CC4350_FNSEL_I2C (5) #define CC4350_FNSEL_MISC0 (6) #define CC4350_FNSEL_GCI (7) #define CC4350_FNSEL_MISC1 (8) #define CC4350_FNSEL_MISC2 (9) #define CC4350_FNSEL_PWDOG (10) #define CC4350_FNSEL_IND (12) #define CC4350_FNSEL_PDN (13) #define CC4350_FNSEL_PUP (14) #define CC4350_FNSEL_TRISTATE (15) /* 4350 GPIO */ #define CC4350_PIN_GPIO_00 (0) #define CC4350_PIN_GPIO_01 (1) #define CC4350_PIN_GPIO_02 (2) #define CC4350_PIN_GPIO_03 (3) #define CC4350_PIN_GPIO_04 (4) #define CC4350_PIN_GPIO_05 (5) #define CC4350_PIN_GPIO_06 (6) #define CC4350_PIN_GPIO_07 (7) #define CC4350_PIN_GPIO_08 (8) #define CC4350_PIN_GPIO_09 (9) #define CC4350_PIN_GPIO_10 (10) #define CC4350_PIN_GPIO_11 (11) #define CC4350_PIN_GPIO_12 (12) #define CC4350_PIN_GPIO_13 (13) #define CC4350_PIN_GPIO_14 (14) #define CC4350_PIN_GPIO_15 (15) #define CC2_4350_MEMLPLDO_PWRSW_EN_MASK (1 << 21) #define CC2_4350_MEMLPLDO_PWRSW_EN_SHIFT (21) #define CC2_4350_SDIO_AOS_WAKEUP_MASK (1 << 24) #define CC2_4350_SDIO_AOS_WAKEUP_SHIFT (24) /* Applies to 4335/4350/4345 */ #define CC3_SR_CLK_SR_MEM_MASK (1 << 0) #define CC3_SR_CLK_SR_MEM_SHIFT (0) #define CC3_SR_BIT1_TBD_MASK (1 << 1) #define CC3_SR_BIT1_TBD_SHIFT (1) #define CC3_SR_ENGINE_ENABLE_MASK (1 << 2) #define CC3_SR_ENGINE_ENABLE_SHIFT (2) #define CC3_SR_BIT3_TBD_MASK (1 << 3) #define CC3_SR_BIT3_TBD_SHIFT (3) #define CC3_SR_MINDIV_FAST_CLK_MASK (0xF << 4) #define CC3_SR_MINDIV_FAST_CLK_SHIFT (4) #define CC3_SR_R23_SR2_RISE_EDGE_TRIG_MASK (1 << 8) #define CC3_SR_R23_SR2_RISE_EDGE_TRIG_SHIFT (8) #define CC3_SR_R23_SR2_FALL_EDGE_TRIG_MASK (1 << 9) #define CC3_SR_R23_SR2_FALL_EDGE_TRIG_SHIFT (9) #define CC3_SR_R23_SR_RISE_EDGE_TRIG_MASK (1 << 10) #define CC3_SR_R23_SR_RISE_EDGE_TRIG_SHIFT (10) #define CC3_SR_R23_SR_FALL_EDGE_TRIG_MASK (1 << 11) #define CC3_SR_R23_SR_FALL_EDGE_TRIG_SHIFT (11) #define CC3_SR_NUM_CLK_HIGH_MASK (0x7 << 12) #define CC3_SR_NUM_CLK_HIGH_SHIFT (12) #define CC3_SR_BIT15_TBD_MASK (1 << 15) #define CC3_SR_BIT15_TBD_SHIFT (15) #define CC3_SR_PHY_FUNC_PIC_MASK (1 << 16) #define CC3_SR_PHY_FUNC_PIC_SHIFT (16) #define CC3_SR_BIT17_19_TBD_MASK (0x7 << 17) #define CC3_SR_BIT17_19_TBD_SHIFT (17) #define CC3_SR_CHIP_TRIGGER_1_MASK (1 << 20) #define CC3_SR_CHIP_TRIGGER_1_SHIFT (20) #define CC3_SR_CHIP_TRIGGER_2_MASK (1 << 21) #define CC3_SR_CHIP_TRIGGER_2_SHIFT (21) #define CC3_SR_CHIP_TRIGGER_3_MASK (1 << 22) #define CC3_SR_CHIP_TRIGGER_3_SHIFT (22) #define CC3_SR_CHIP_TRIGGER_4_MASK (1 << 23) #define CC3_SR_CHIP_TRIGGER_4_SHIFT (23) #define CC3_SR_ALLOW_SBC_FUNC_PIC_MASK (1 << 24) #define CC3_SR_ALLOW_SBC_FUNC_PIC_SHIFT (24) #define CC3_SR_BIT25_26_TBD_MASK (0x3 << 25) #define CC3_SR_BIT25_26_TBD_SHIFT (25) #define CC3_SR_ALLOW_SBC_STBY_MASK (1 << 27) #define CC3_SR_ALLOW_SBC_STBY_SHIFT (27) #define CC3_SR_GPIO_MUX_MASK (0xF << 28) #define CC3_SR_GPIO_MUX_SHIFT (28) /* Applies to 4335/4350/4345 */ #define CC4_SR_INIT_ADDR_MASK (0x3FF0000) #define CC4_4350_SR_ASM_ADDR (0x30) #define CC4_4335_SR_ASM_ADDR (0x48) #define CC4_SR_INIT_ADDR_SHIFT (16) #define CC4_4350_EN_SR_CLK_ALP_MASK (1 << 30) #define CC4_4350_EN_SR_CLK_ALP_SHIFT (30) #define CC4_4350_EN_SR_CLK_HT_MASK (1 << 31) #define CC4_4350_EN_SR_CLK_HT_SHIFT (31) #define VREG4_4350_MEMLPDO_PU_MASK (1 << 31) #define VREG4_4350_MEMLPDO_PU_SHIFT 31 #define CC6_4350_PCIE_CLKREQ_WAKEUP_MASK (1 << 4) #define CC6_4350_PCIE_CLKREQ_WAKEUP_SHIFT (4) #define CC6_4350_PMU_WAKEUP_ALPAVAIL_MASK (1 << 6) #define CC6_4350_PMU_WAKEUP_ALPAVAIL_SHIFT (6) /* GCI chipcontrol register indices */ #define CC_GCI_CHIPCTRL_00 (0) #define CC_GCI_CHIPCTRL_01 (1) #define CC_GCI_CHIPCTRL_02 (2) #define CC_GCI_CHIPCTRL_03 (3) #define CC_GCI_CHIPCTRL_04 (4) #define CC_GCI_CHIPCTRL_05 (5) #define CC_GCI_CHIPCTRL_06 (6) #define CC_GCI_CHIPCTRL_07 (7) #define CC_GCI_CHIPCTRL_08 (8) #define CC_GCI_06_JTAG_SEL_SHIFT 4 #define CC_GCI_06_JTAG_SEL_MASK (1 << 4) #define CC_GCI_NUMCHIPCTRLREGS(cap1) ((cap1 & 0xF00) >> 8) /* 4335 pins * note: only the values set as default/used are added here. */ #define CC4335_PIN_GPIO_00 (0) #define CC4335_PIN_GPIO_01 (1) #define CC4335_PIN_GPIO_02 (2) #define CC4335_PIN_GPIO_03 (3) #define CC4335_PIN_GPIO_04 (4) #define CC4335_PIN_GPIO_05 (5) #define CC4335_PIN_GPIO_06 (6) #define CC4335_PIN_GPIO_07 (7) #define CC4335_PIN_GPIO_08 (8) #define CC4335_PIN_GPIO_09 (9) #define CC4335_PIN_GPIO_10 (10) #define CC4335_PIN_GPIO_11 (11) #define CC4335_PIN_GPIO_12 (12) #define CC4335_PIN_GPIO_13 (13) #define CC4335_PIN_GPIO_14 (14) #define CC4335_PIN_GPIO_15 (15) #define CC4335_PIN_SDIO_CLK (16) #define CC4335_PIN_SDIO_CMD (17) #define CC4335_PIN_SDIO_DATA0 (18) #define CC4335_PIN_SDIO_DATA1 (19) #define CC4335_PIN_SDIO_DATA2 (20) #define CC4335_PIN_SDIO_DATA3 (21) #define CC4335_PIN_RF_SW_CTRL_0 (22) #define CC4335_PIN_RF_SW_CTRL_1 (23) #define CC4335_PIN_RF_SW_CTRL_2 (24) #define CC4335_PIN_RF_SW_CTRL_3 (25) #define CC4335_PIN_RF_SW_CTRL_4 (26) #define CC4335_PIN_RF_SW_CTRL_5 (27) #define CC4335_PIN_RF_SW_CTRL_6 (28) #define CC4335_PIN_RF_SW_CTRL_7 (29) #define CC4335_PIN_RF_SW_CTRL_8 (30) #define CC4335_PIN_RF_SW_CTRL_9 (31) /* 4335 GCI function sel values */ #define CC4335_FNSEL_HWDEF (0) #define CC4335_FNSEL_SAMEASPIN (1) #define CC4335_FNSEL_GPIO0 (2) #define CC4335_FNSEL_GPIO1 (3) #define CC4335_FNSEL_GCI0 (4) #define CC4335_FNSEL_GCI1 (5) #define CC4335_FNSEL_UART (6) #define CC4335_FNSEL_SFLASH (7) #define CC4335_FNSEL_SPROM (8) #define CC4335_FNSEL_MISC0 (9) #define CC4335_FNSEL_MISC1 (10) #define CC4335_FNSEL_MISC2 (11) #define CC4335_FNSEL_IND (12) #define CC4335_FNSEL_PDN (13) #define CC4335_FNSEL_PUP (14) #define CC4335_FNSEL_TRI (15) /* find the 4 bit mask given the bit position */ #define GCIMASK(pos) (((uint32)0xF) << pos) /* get the value which can be used to directly OR with chipcontrol reg */ #define GCIPOSVAL(val, pos) ((((uint32)val) << pos) & GCIMASK(pos)) /* 4335 MUX options. each nibble belongs to a setting. Non-zero value specifies a logic * for now only UART for bootloader. */ #define MUXENAB4335_UART_MASK (0x0000000f) #define MUXENAB4335_UART_SHIFT 0 #define MUXENAB4335_HOSTWAKE_MASK (0x000000f0) /* configure GPIO for SDIO host_wake */ #define MUXENAB4335_HOSTWAKE_SHIFT 4 #define MUXENAB4335_GETIX(val, name) \ ((((val) & MUXENAB4335_ ## name ## _MASK) >> MUXENAB4335_ ## name ## _SHIFT) - 1) /* defines to detect active host interface in use */ #define CHIP_HOSTIF_USB(sih) (si_chip_hostif(sih) & CST4360_MODE_USB) /* * Maximum delay for the PMU state transition in us. * This is an upper bound intended for spinwaits etc. */ #define PMU_MAX_TRANSITION_DLY 15000 /* PMU resource up transition time in ILP cycles */ #define PMURES_UP_TRANSITION 2 /* SECI configuration */ #define SECI_MODE_UART 0x0 #define SECI_MODE_SECI 0x1 #define SECI_MODE_LEGACY_3WIRE_BT 0x2 #define SECI_MODE_LEGACY_3WIRE_WLAN 0x3 #define SECI_MODE_HALF_SECI 0x4 #define SECI_RESET (1 << 0) #define SECI_RESET_BAR_UART (1 << 1) #define SECI_ENAB_SECI_ECI (1 << 2) #define SECI_ENAB_SECIOUT_DIS (1 << 3) #define SECI_MODE_MASK 0x7 #define SECI_MODE_SHIFT 4 /* (bits 5, 6, 7) */ #define SECI_UPD_SECI (1 << 7) #define SECI_SIGNOFF_0 0xDB #define SECI_SIGNOFF_1 0 /* seci clk_ctl_st bits */ #define CLKCTL_STS_SECI_CLK_REQ (1 << 8) #define CLKCTL_STS_SECI_CLK_AVAIL (1 << 24) #define SECI_UART_MSR_CTS_STATE (1 << 0) #define SECI_UART_MSR_RTS_STATE (1 << 1) #define SECI_UART_SECI_IN_STATE (1 << 2) #define SECI_UART_SECI_IN2_STATE (1 << 3) /* SECI UART LCR/MCR register bits */ #define SECI_UART_LCR_STOP_BITS (1 << 0) /* 0 - 1bit, 1 - 2bits */ #define SECI_UART_LCR_PARITY_EN (1 << 1) #define SECI_UART_LCR_PARITY (1 << 2) /* 0 - odd, 1 - even */ #define SECI_UART_LCR_RX_EN (1 << 3) #define SECI_UART_LCR_LBRK_CTRL (1 << 4) /* 1 => SECI_OUT held low */ #define SECI_UART_LCR_TXO_EN (1 << 5) #define SECI_UART_LCR_RTSO_EN (1 << 6) #define SECI_UART_LCR_SLIPMODE_EN (1 << 7) #define SECI_UART_LCR_RXCRC_CHK (1 << 8) #define SECI_UART_LCR_TXCRC_INV (1 << 9) #define SECI_UART_LCR_TXCRC_LSBF (1 << 10) #define SECI_UART_LCR_TXCRC_EN (1 << 11) #define SECI_UART_MCR_TX_EN (1 << 0) #define SECI_UART_MCR_PRTS (1 << 1) #define SECI_UART_MCR_SWFLCTRL_EN (1 << 2) #define SECI_UART_MCR_HIGHRATE_EN (1 << 3) #define SECI_UART_MCR_LOOPBK_EN (1 << 4) #define SECI_UART_MCR_AUTO_RTS (1 << 5) #define SECI_UART_MCR_AUTO_TX_DIS (1 << 6) #define SECI_UART_MCR_BAUD_ADJ_EN (1 << 7) #define SECI_UART_MCR_XONOFF_RPT (1 << 9) /* WLAN channel numbers - used from wifi.h */ /* WLAN BW */ #define ECI_BW_20 0x0 #define ECI_BW_25 0x1 #define ECI_BW_30 0x2 #define ECI_BW_35 0x3 #define ECI_BW_40 0x4 #define ECI_BW_45 0x5 #define ECI_BW_50 0x6 #define ECI_BW_ALL 0x7 /* WLAN - number of antenna */ #define WLAN_NUM_ANT1 TXANT_0 #define WLAN_NUM_ANT2 TXANT_1 #endif /* _SBCHIPC_H */