/* * SDIO Host Controller Spec header file * Register map and definitions for the Standard Host Controller * * Copyright (C) 1999-2013, Broadcom Corporation * * Unless you and Broadcom execute a separate written software license * agreement governing use of this software, this software is licensed to you * under the terms of the GNU General Public License version 2 (the "GPL"), * available at http://www.broadcom.com/licenses/GPLv2.php, with the * following added to such license: * * As a special exception, the copyright holders of this software give you * permission to link this software with independent modules, and to copy and * distribute the resulting executable under terms of your choice, provided that * you also meet, for each linked independent module, the terms and conditions of * the license of that module. An independent module is a module which is not * derived from this software. The special exception does not apply to any * modifications of the software. * * Notwithstanding the above, under no circumstances may you combine this * software in any way with any other Broadcom software provided under a license * other than the GPL, without Broadcom's express prior written consent. * * $Id: sdioh.h 345499 2012-07-18 06:59:05Z $ */ #ifndef _SDIOH_H #define _SDIOH_H #define SD_SysAddr 0x000 #define SD_BlockSize 0x004 #define SD_BlockCount 0x006 #define SD_Arg0 0x008 #define SD_Arg1 0x00A #define SD_TransferMode 0x00C #define SD_Command 0x00E #define SD_Response0 0x010 #define SD_Response1 0x012 #define SD_Response2 0x014 #define SD_Response3 0x016 #define SD_Response4 0x018 #define SD_Response5 0x01A #define SD_Response6 0x01C #define SD_Response7 0x01E #define SD_BufferDataPort0 0x020 #define SD_BufferDataPort1 0x022 #define SD_PresentState 0x024 #define SD_HostCntrl 0x028 #define SD_PwrCntrl 0x029 #define SD_BlockGapCntrl 0x02A #define SD_WakeupCntrl 0x02B #define SD_ClockCntrl 0x02C #define SD_TimeoutCntrl 0x02E #define SD_SoftwareReset 0x02F #define SD_IntrStatus 0x030 #define SD_ErrorIntrStatus 0x032 #define SD_IntrStatusEnable 0x034 #define SD_ErrorIntrStatusEnable 0x036 #define SD_IntrSignalEnable 0x038 #define SD_ErrorIntrSignalEnable 0x03A #define SD_CMD12ErrorStatus 0x03C #define SD_Capabilities 0x040 #define SD_Capabilities3 0x044 #define SD_MaxCurCap 0x048 #define SD_MaxCurCap_Reserved 0x04C #define SD_ADMA_ErrStatus 0x054 #define SD_ADMA_SysAddr 0x58 #define SD_SlotInterruptStatus 0x0FC #define SD_HostControllerVersion 0x0FE #define SD_GPIO_Reg 0x100 #define SD_GPIO_OE 0x104 #define SD_GPIO_Enable 0x108 /* SD specific registers in PCI config space */ #define SD_SlotInfo 0x40 /* HC 3.0 specific registers and offsets */ #define SD3_HostCntrl2 0x03E /* preset regsstart and count */ #define SD3_PresetValStart 0x060 #define SD3_PresetValCount 8 /* preset-indiv regs */ #define SD3_PresetVal_init 0x060 #define SD3_PresetVal_default 0x062 #define SD3_PresetVal_HS 0x064 #define SD3_PresetVal_SDR12 0x066 #define SD3_PresetVal_SDR25 0x068 #define SD3_PresetVal_SDR50 0x06a #define SD3_PresetVal_SDR104 0x06c #define SD3_PresetVal_DDR50 0x06e /* SDIO3.0 Revx specific Registers */ #define SD3_Tuning_Info_Register 0x0EC #define SD3_WL_BT_reset_register 0x0F0 /* preset value indices */ #define SD3_PRESETVAL_INITIAL_IX 0 #define SD3_PRESETVAL_DESPEED_IX 1 #define SD3_PRESETVAL_HISPEED_IX 2 #define SD3_PRESETVAL_SDR12_IX 3 #define SD3_PRESETVAL_SDR25_IX 4 #define SD3_PRESETVAL_SDR50_IX 5 #define SD3_PRESETVAL_SDR104_IX 6 #define SD3_PRESETVAL_DDR50_IX 7 /* SD_Capabilities reg (0x040) */ #define CAP_TO_CLKFREQ_M BITFIELD_MASK(6) #define CAP_TO_CLKFREQ_S 0 #define CAP_TO_CLKUNIT_M BITFIELD_MASK(1) #define CAP_TO_CLKUNIT_S 7 /* Note: for sdio-2.0 case, this mask has to be 6 bits, but msb 2 bits are reserved. going ahead with 8 bits, as it is req for 3.0 */ #define CAP_BASECLK_M BITFIELD_MASK(8) #define CAP_BASECLK_S 8 #define CAP_MAXBLOCK_M BITFIELD_MASK(2) #define CAP_MAXBLOCK_S 16 #define CAP_ADMA2_M BITFIELD_MASK(1) #define CAP_ADMA2_S 19 #define CAP_ADMA1_M BITFIELD_MASK(1) #define CAP_ADMA1_S 20 #define CAP_HIGHSPEED_M BITFIELD_MASK(1) #define CAP_HIGHSPEED_S 21 #define CAP_DMA_M BITFIELD_MASK(1) #define CAP_DMA_S 22 #define CAP_SUSPEND_M BITFIELD_MASK(1) #define CAP_SUSPEND_S 23 #define CAP_VOLT_3_3_M BITFIELD_MASK(1) #define CAP_VOLT_3_3_S 24 #define CAP_VOLT_3_0_M BITFIELD_MASK(1) #define CAP_VOLT_3_0_S 25 #define CAP_VOLT_1_8_M BITFIELD_MASK(1) #define CAP_VOLT_1_8_S 26 #define CAP_64BIT_HOST_M BITFIELD_MASK(1) #define CAP_64BIT_HOST_S 28 #define SDIO_OCR_READ_FAIL (2) #define CAP_ASYNCINT_SUP_M BITFIELD_MASK(1) #define CAP_ASYNCINT_SUP_S 29 #define CAP_SLOTTYPE_M BITFIELD_MASK(2) #define CAP_SLOTTYPE_S 30 #define CAP3_MSBits_OFFSET (32) /* note: following are caps MSB32 bits. So the bits start from 0, instead of 32. that is why CAP3_MSBits_OFFSET is subtracted. */ #define CAP3_SDR50_SUP_M BITFIELD_MASK(1) #define CAP3_SDR50_SUP_S (32 - CAP3_MSBits_OFFSET) #define CAP3_SDR104_SUP_M BITFIELD_MASK(1) #define CAP3_SDR104_SUP_S (33 - CAP3_MSBits_OFFSET) #define CAP3_DDR50_SUP_M BITFIELD_MASK(1) #define CAP3_DDR50_SUP_S (34 - CAP3_MSBits_OFFSET) /* for knowing the clk caps in a single read */ #define CAP3_30CLKCAP_M BITFIELD_MASK(3) #define CAP3_30CLKCAP_S (32 - CAP3_MSBits_OFFSET) #define CAP3_DRIVTYPE_A_M BITFIELD_MASK(1) #define CAP3_DRIVTYPE_A_S (36 - CAP3_MSBits_OFFSET) #define CAP3_DRIVTYPE_C_M BITFIELD_MASK(1) #define CAP3_DRIVTYPE_C_S (37 - CAP3_MSBits_OFFSET) #define CAP3_DRIVTYPE_D_M BITFIELD_MASK(1) #define CAP3_DRIVTYPE_D_S (38 - CAP3_MSBits_OFFSET) #define CAP3_RETUNING_TC_M BITFIELD_MASK(4) #define CAP3_RETUNING_TC_S (40 - CAP3_MSBits_OFFSET) #define CAP3_TUNING_SDR50_M BITFIELD_MASK(1) #define CAP3_TUNING_SDR50_S (45 - CAP3_MSBits_OFFSET) #define CAP3_RETUNING_MODES_M BITFIELD_MASK(2) #define CAP3_RETUNING_MODES_S (46 - CAP3_MSBits_OFFSET) #define CAP3_CLK_MULT_M BITFIELD_MASK(8) #define CAP3_CLK_MULT_S (48 - CAP3_MSBits_OFFSET) #define PRESET_DRIVR_SELECT_M BITFIELD_MASK(2) #define PRESET_DRIVR_SELECT_S 14 #define PRESET_CLK_DIV_M BITFIELD_MASK(10) #define PRESET_CLK_DIV_S 0 /* SD_MaxCurCap reg (0x048) */ #define CAP_CURR_3_3_M BITFIELD_MASK(8) #define CAP_CURR_3_3_S 0 #define CAP_CURR_3_0_M BITFIELD_MASK(8) #define CAP_CURR_3_0_S 8 #define CAP_CURR_1_8_M BITFIELD_MASK(8) #define CAP_CURR_1_8_S 16 /* SD_SysAddr: Offset 0x0000, Size 4 bytes */ /* SD_BlockSize: Offset 0x004, Size 2 bytes */ #define BLKSZ_BLKSZ_M BITFIELD_MASK(12) #define BLKSZ_BLKSZ_S 0 #define BLKSZ_BNDRY_M BITFIELD_MASK(3) #define BLKSZ_BNDRY_S 12 /* SD_BlockCount: Offset 0x006, size 2 bytes */ /* SD_Arg0: Offset 0x008, size = 4 bytes */ /* SD_TransferMode Offset 0x00C, size = 2 bytes */ #define XFER_DMA_ENABLE_M BITFIELD_MASK(1) #define XFER_DMA_ENABLE_S 0 #define XFER_BLK_COUNT_EN_M BITFIELD_MASK(1) #define XFER_BLK_COUNT_EN_S 1 #define XFER_CMD_12_EN_M BITFIELD_MASK(1) #define XFER_CMD_12_EN_S 2 #define XFER_DATA_DIRECTION_M BITFIELD_MASK(1) #define XFER_DATA_DIRECTION_S 4 #define XFER_MULTI_BLOCK_M BITFIELD_MASK(1) #define XFER_MULTI_BLOCK_S 5 /* SD_Command: Offset 0x00E, size = 2 bytes */ /* resp_type field */ #define RESP_TYPE_NONE 0 #define RESP_TYPE_136 1 #define RESP_TYPE_48 2 #define RESP_TYPE_48_BUSY 3 /* type field */ #define CMD_TYPE_NORMAL 0 #define CMD_TYPE_SUSPEND 1 #define CMD_TYPE_RESUME 2 #define CMD_TYPE_ABORT 3 #define CMD_RESP_TYPE_M BITFIELD_MASK(2) /* Bits [0-1] - Response type */ #define CMD_RESP_TYPE_S 0 #define CMD_CRC_EN_M BITFIELD_MASK(1) /* Bit 3 - CRC enable */ #define CMD_CRC_EN_S 3 #define CMD_INDEX_EN_M BITFIELD_MASK(1) /* Bit 4 - Enable index checking */ #define CMD_INDEX_EN_S 4 #define CMD_DATA_EN_M BITFIELD_MASK(1) /* Bit 5 - Using DAT line */ #define CMD_DATA_EN_S 5 #define CMD_TYPE_M BITFIELD_MASK(2) /* Bit [6-7] - Normal, abort, resume, etc */ #define CMD_TYPE_S 6 #define CMD_INDEX_M BITFIELD_MASK(6) /* Bits [8-13] - Command number */ #define CMD_INDEX_S 8 /* SD_BufferDataPort0 : Offset 0x020, size = 2 or 4 bytes */ /* SD_BufferDataPort1 : Offset 0x022, size = 2 bytes */ /* SD_PresentState : Offset 0x024, size = 4 bytes */ #define PRES_CMD_INHIBIT_M BITFIELD_MASK(1) /* Bit 0 May use CMD */ #define PRES_CMD_INHIBIT_S 0 #define PRES_DAT_INHIBIT_M BITFIELD_MASK(1) /* Bit 1 May use DAT */ #define PRES_DAT_INHIBIT_S 1 #define PRES_DAT_BUSY_M BITFIELD_MASK(1) /* Bit 2 DAT is busy */ #define PRES_DAT_BUSY_S 2 #define PRES_PRESENT_RSVD_M BITFIELD_MASK(5) /* Bit [3-7] rsvd */ #define PRES_PRESENT_RSVD_S 3 #define PRES_WRITE_ACTIVE_M BITFIELD_MASK(1) /* Bit 8 Write is active */ #define PRES_WRITE_ACTIVE_S 8 #define PRES_READ_ACTIVE_M BITFIELD_MASK(1) /* Bit 9 Read is active */ #define PRES_READ_ACTIVE_S 9 #define PRES_WRITE_DATA_RDY_M BITFIELD_MASK(1) /* Bit 10 Write buf is avail */ #define PRES_WRITE_DATA_RDY_S 10 #define PRES_READ_DATA_RDY_M BITFIELD_MASK(1) /* Bit 11 Read buf data avail */ #define PRES_READ_DATA_RDY_S 11 #define PRES_CARD_PRESENT_M BITFIELD_MASK(1) /* Bit 16 Card present - debounced */ #define PRES_CARD_PRESENT_S 16 #define PRES_CARD_STABLE_M BITFIELD_MASK(1) /* Bit 17 Debugging */ #define PRES_CARD_STABLE_S 17 #define PRES_CARD_PRESENT_RAW_M BITFIELD_MASK(1) /* Bit 18 Not debounced */ #define PRES_CARD_PRESENT_RAW_S 18 #define PRES_WRITE_ENABLED_M BITFIELD_MASK(1) /* Bit 19 Write protected? */ #define PRES_WRITE_ENABLED_S 19 #define PRES_DAT_SIGNAL_M BITFIELD_MASK(4) /* Bit [20-23] Debugging */ #define PRES_DAT_SIGNAL_S 20 #define PRES_CMD_SIGNAL_M BITFIELD_MASK(1) /* Bit 24 Debugging */ #define PRES_CMD_SIGNAL_S 24 /* SD_HostCntrl: Offset 0x028, size = 1 bytes */ #define HOST_LED_M BITFIELD_MASK(1) /* Bit 0 LED On/Off */ #define HOST_LED_S 0 #define HOST_DATA_WIDTH_M BITFIELD_MASK(1) /* Bit 1 4 bit enable */ #define HOST_DATA_WIDTH_S 1 #define HOST_HI_SPEED_EN_M BITFIELD_MASK(1) /* Bit 2 High speed vs low speed */ #define HOST_DMA_SEL_S 3 #define HOST_DMA_SEL_M BITFIELD_MASK(2) /* Bit 4:3 DMA Select */ #define HOST_HI_SPEED_EN_S 2 /* Host Control2: */ #define HOSTCtrl2_PRESVAL_EN_M BITFIELD_MASK(1) /* 1 bit */ #define HOSTCtrl2_PRESVAL_EN_S 15 /* bit# */ #define HOSTCtrl2_ASYINT_EN_M BITFIELD_MASK(1) /* 1 bit */ #define HOSTCtrl2_ASYINT_EN_S 14 /* bit# */ #define HOSTCtrl2_SAMPCLK_SEL_M BITFIELD_MASK(1) /* 1 bit */ #define HOSTCtrl2_SAMPCLK_SEL_S 7 /* bit# */ #define HOSTCtrl2_EXEC_TUNING_M BITFIELD_MASK(1) /* 1 bit */ #define HOSTCtrl2_EXEC_TUNING_S 6 /* bit# */ #define HOSTCtrl2_DRIVSTRENGTH_SEL_M BITFIELD_MASK(2) /* 2 bit */ #define HOSTCtrl2_DRIVSTRENGTH_SEL_S 4 /* bit# */ #define HOSTCtrl2_1_8SIG_EN_M BITFIELD_MASK(1) /* 1 bit */ #define HOSTCtrl2_1_8SIG_EN_S 3 /* bit# */ #define HOSTCtrl2_UHSMODE_SEL_M BITFIELD_MASK(3) /* 3 bit */ #define HOSTCtrl2_UHSMODE_SEL_S 0 /* bit# */ #define HOST_CONTR_VER_2 (1) #define HOST_CONTR_VER_3 (2) /* misc defines */ #define SD1_MODE 0x1 /* SD Host Cntrlr Spec */ #define SD4_MODE 0x2 /* SD Host Cntrlr Spec */ /* SD_PwrCntrl: Offset 0x029, size = 1 bytes */ #define PWR_BUS_EN_M BITFIELD_MASK(1) /* Bit 0 Power the bus */ #define PWR_BUS_EN_S 0 #define PWR_VOLTS_M BITFIELD_MASK(3) /* Bit [1-3] Voltage Select */ #define PWR_VOLTS_S 1 /* SD_SoftwareReset: Offset 0x02F, size = 1 byte */ #define SW_RESET_ALL_M BITFIELD_MASK(1) /* Bit 0 Reset All */ #define SW_RESET_ALL_S 0 #define SW_RESET_CMD_M BITFIELD_MASK(1) /* Bit 1 CMD Line Reset */ #define SW_RESET_CMD_S 1 #define SW_RESET_DAT_M BITFIELD_MASK(1) /* Bit 2 DAT Line Reset */ #define SW_RESET_DAT_S 2 /* SD_IntrStatus: Offset 0x030, size = 2 bytes */ /* Defs also serve SD_IntrStatusEnable and SD_IntrSignalEnable */ #define INTSTAT_CMD_COMPLETE_M BITFIELD_MASK(1) /* Bit 0 */ #define INTSTAT_CMD_COMPLETE_S 0 #define INTSTAT_XFER_COMPLETE_M BITFIELD_MASK(1) #define INTSTAT_XFER_COMPLETE_S 1 #define INTSTAT_BLOCK_GAP_EVENT_M BITFIELD_MASK(1) #define INTSTAT_BLOCK_GAP_EVENT_S 2 #define INTSTAT_DMA_INT_M BITFIELD_MASK(1) #define INTSTAT_DMA_INT_S 3 #define INTSTAT_BUF_WRITE_READY_M BITFIELD_MASK(1) #define INTSTAT_BUF_WRITE_READY_S 4 #define INTSTAT_BUF_READ_READY_M BITFIELD_MASK(1) #define INTSTAT_BUF_READ_READY_S 5 #define INTSTAT_CARD_INSERTION_M BITFIELD_MASK(1) #define INTSTAT_CARD_INSERTION_S 6 #define INTSTAT_CARD_REMOVAL_M BITFIELD_MASK(1) #define INTSTAT_CARD_REMOVAL_S 7 #define INTSTAT_CARD_INT_M BITFIELD_MASK(1) #define INTSTAT_CARD_INT_S 8 #define INTSTAT_RETUNING_INT_M BITFIELD_MASK(1) /* Bit 12 */ #define INTSTAT_RETUNING_INT_S 12 #define INTSTAT_ERROR_INT_M BITFIELD_MASK(1) /* Bit 15 */ #define INTSTAT_ERROR_INT_S 15 /* SD_ErrorIntrStatus: Offset 0x032, size = 2 bytes */ /* Defs also serve SD_ErrorIntrStatusEnable and SD_ErrorIntrSignalEnable */ #define ERRINT_CMD_TIMEOUT_M BITFIELD_MASK(1) #define ERRINT_CMD_TIMEOUT_S 0 #define ERRINT_CMD_CRC_M BITFIELD_MASK(1) #define ERRINT_CMD_CRC_S 1 #define ERRINT_CMD_ENDBIT_M BITFIELD_MASK(1) #define ERRINT_CMD_ENDBIT_S 2 #define ERRINT_CMD_INDEX_M BITFIELD_MASK(1) #define ERRINT_CMD_INDEX_S 3 #define ERRINT_DATA_TIMEOUT_M BITFIELD_MASK(1) #define ERRINT_DATA_TIMEOUT_S 4 #define ERRINT_DATA_CRC_M BITFIELD_MASK(1) #define ERRINT_DATA_CRC_S 5 #define ERRINT_DATA_ENDBIT_M BITFIELD_MASK(1) #define ERRINT_DATA_ENDBIT_S 6 #define ERRINT_CURRENT_LIMIT_M BITFIELD_MASK(1) #define ERRINT_CURRENT_LIMIT_S 7 #define ERRINT_AUTO_CMD12_M BITFIELD_MASK(1) #define ERRINT_AUTO_CMD12_S 8 #define ERRINT_VENDOR_M BITFIELD_MASK(4) #define ERRINT_VENDOR_S 12 #define ERRINT_ADMA_M BITFIELD_MASK(1) #define ERRINT_ADMA_S 9 /* Also provide definitions in "normal" form to allow combined masks */ #define ERRINT_CMD_TIMEOUT_BIT 0x0001 #define ERRINT_CMD_CRC_BIT 0x0002 #define ERRINT_CMD_ENDBIT_BIT 0x0004 #define ERRINT_CMD_INDEX_BIT 0x0008 #define ERRINT_DATA_TIMEOUT_BIT 0x0010 #define ERRINT_DATA_CRC_BIT 0x0020 #define ERRINT_DATA_ENDBIT_BIT 0x0040 #define ERRINT_CURRENT_LIMIT_BIT 0x0080 #define ERRINT_AUTO_CMD12_BIT 0x0100 #define ERRINT_ADMA_BIT 0x0200 /* Masks to select CMD vs. DATA errors */ #define ERRINT_CMD_ERRS (ERRINT_CMD_TIMEOUT_BIT | ERRINT_CMD_CRC_BIT |\ ERRINT_CMD_ENDBIT_BIT | ERRINT_CMD_INDEX_BIT) #define ERRINT_DATA_ERRS (ERRINT_DATA_TIMEOUT_BIT | ERRINT_DATA_CRC_BIT |\ ERRINT_DATA_ENDBIT_BIT | ERRINT_ADMA_BIT) #define ERRINT_TRANSFER_ERRS (ERRINT_CMD_ERRS | ERRINT_DATA_ERRS) /* SD_WakeupCntr_BlockGapCntrl : Offset 0x02A , size = bytes */ /* SD_ClockCntrl : Offset 0x02C , size = bytes */ /* SD_SoftwareReset_TimeoutCntrl : Offset 0x02E , size = bytes */ /* SD_IntrStatus : Offset 0x030 , size = bytes */ /* SD_ErrorIntrStatus : Offset 0x032 , size = bytes */ /* SD_IntrStatusEnable : Offset 0x034 , size = bytes */ /* SD_ErrorIntrStatusEnable : Offset 0x036 , size = bytes */ /* SD_IntrSignalEnable : Offset 0x038 , size = bytes */ /* SD_ErrorIntrSignalEnable : Offset 0x03A , size = bytes */ /* SD_CMD12ErrorStatus : Offset 0x03C , size = bytes */ /* SD_Capabilities : Offset 0x040 , size = bytes */ /* SD_MaxCurCap : Offset 0x048 , size = bytes */ /* SD_MaxCurCap_Reserved: Offset 0x04C , size = bytes */ /* SD_SlotInterruptStatus: Offset 0x0FC , size = bytes */ /* SD_HostControllerVersion : Offset 0x0FE , size = bytes */ /* SDIO Host Control Register DMA Mode Definitions */ #define SDIOH_SDMA_MODE 0 #define SDIOH_ADMA1_MODE 1 #define SDIOH_ADMA2_MODE 2 #define SDIOH_ADMA2_64_MODE 3 #define ADMA2_ATTRIBUTE_VALID (1 << 0) /* ADMA Descriptor line valid */ #define ADMA2_ATTRIBUTE_END (1 << 1) /* End of Descriptor */ #define ADMA2_ATTRIBUTE_INT (1 << 2) /* Interrupt when line is done */ #define ADMA2_ATTRIBUTE_ACT_NOP (0 << 4) /* Skip current line, go to next. */ #define ADMA2_ATTRIBUTE_ACT_RSV (1 << 4) /* Same as NOP */ #define ADMA1_ATTRIBUTE_ACT_SET (1 << 4) /* ADMA1 Only - set transfer length */ #define ADMA2_ATTRIBUTE_ACT_TRAN (2 << 4) /* Transfer Data of one descriptor line. */ #define ADMA2_ATTRIBUTE_ACT_LINK (3 << 4) /* Link Descriptor */ /* ADMA2 Descriptor Table Entry for 32-bit Address */ typedef struct adma2_dscr_32b { uint32 len_attr; uint32 phys_addr; } adma2_dscr_32b_t; /* ADMA1 Descriptor Table Entry */ typedef struct adma1_dscr { uint32 phys_addr_attr; } adma1_dscr_t; #endif /* _SDIOH_H */