qmk_firmware/keyboards/zygomorph/rules.mk

70 lines
3.1 KiB
Makefile
Raw Normal View History

[Keyboard] Adding RGBKB Zygomorph Keyboard (#5841) * Initial Zygomorph 5x6 code Split is not working yet * layout changes implement 4 row config option (not done yet), remove layout comments in layout.c * Zygomorph layouts for 5x12, 5x6, 4x12, and 4x6 Also, info.json *should* be nearly usable for the configurator * temporary fix for pin D5 being broken * show D5 issue comment * add build notes * Pin B7 broken in split why? * remove fix * Fix some pin assignments * begin to fix keymap * Create new 5x6 layout * update key positions * Initial Zygomorph 5x6 code Split is not working yet * layout changes implement 4 row config option (not done yet), remove layout comments in layout.c * Zygomorph layouts for 5x12, 5x6, 4x12, and 4x6 Also, info.json *should* be nearly usable for the configurator * temporary fix for pin D5 being broken * show D5 issue comment * add build notes * Pin B7 broken in split why? * remove fix * Fix some pin assignments * begin to fix keymap * Create new 5x6 layout * Rough first pass at split common conversion. Keymap cleanup to cover just the basics. Broke OLED code out into separate example. * Fix readme * Removal of old encoder / oled driver, fix for layout macros * small update * xulkal zygomorph keymaps * Removed the LED_MIRRORED option as leds are always mirrored on Zygomorph * Xulkal keymaps update * split rgb light support * fix line endings * Apply suggestions from code review Co-Authored-By: zvecr <git@zvecr.com> * More layout and compile fixes from pr review * Cleaning up rules.mk files * Apply suggestions from code review Co-Authored-By: zvecr <git@zvecr.com> * Updating defaults * Apply suggestions from code review Co-Authored-By: noroadsleft <18669334+noroadsleft@users.noreply.github.com>
2019-05-12 05:42:57 +00:00
# MCU name
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Bootloader
# This definition is optional, and if your keyboard supports multiple bootloaders of
# different sizes, comment this out, and the correct address will be loaded
# automatically (+60). See bootloader.mk for all options.
BOOTLOADER = qmk-dfu
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Build Options
# change yes to no to disable
#
BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = no # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
CONSOLE_ENABLE = no # Console for debug(+400)
COMMAND_ENABLE = no # Commands for debug and configuration
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
NKRO_ENABLE = no # USB Nkey Rollover
BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default
RGBLIGHT_ENABLE = yes # Enable keyboard RGB underglow
MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config)
UNICODE_ENABLE = no # Unicode
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE = no # Audio output on port C6
FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches
HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400)
SPLIT_KEYBOARD = yes
LAYOUTS = ortho_4x12 ortho_5x12
DEFAULT_FOLDER = zygomorph/rev1