qmk_firmware/quantum/config_common.h

117 lines
2.5 KiB
C
Raw Normal View History

2015-10-26 20:32:37 +00:00
#ifndef CONFIG_DEFINITIONS_H
#define CONFIG_DEFINITIONS_H
#define B0 0x20
#define B1 0x21
#define B2 0x22
#define B3 0x23
#define B4 0x24
#define B5 0x25
#define B6 0x26
#define B7 0x27
#define C0 0x30
#define C1 0x31
#define C2 0x32
#define C3 0x33
#define C4 0x34
#define C5 0x35
#define C6 0x36
#define C7 0x37
#define D0 0x40
#define D1 0x41
#define D2 0x42
#define D3 0x43
#define D4 0x44
#define D5 0x45
#define D6 0x46
#define D7 0x47
#define E0 0x50
#define E1 0x51
#define E2 0x52
#define E3 0x53
#define E4 0x54
#define E5 0x55
#define E6 0x56
#define E7 0x57
#define F0 0x60
#define F1 0x61
#define F2 0x62
#define F3 0x63
#define F4 0x64
#define F5 0x65
#define F6 0x66
#define F7 0x67
#define COL2ROW 0x0
#define ROW2COL 0x1
#ifdef BLUETOOTH_ENABLE
#ifdef __AVR_ATmega32U4__
#define SERIAL_UART_BAUD 9600
#define SERIAL_UART_DATA UDR1
#define SERIAL_UART_UBRR ((F_CPU/(16UL*SERIAL_UART_BAUD))-1)
#define SERIAL_UART_RXD_VECT USART1_RX_vect
#define SERIAL_UART_TXD_READY (UCSR1A&(1<<UDRE1))
#define SERIAL_UART_INIT() do { \
UBRR1L = (uint8_t) SERIAL_UART_UBRR; /* baud rate */ \
UBRR1H = (uint8_t) (SERIAL_UART_UBRR>>8); /* baud rate */ \
UCSR1B = (1<<TXEN1); /* TX: enable */ \
UCSR1C = (0<<UPM11) | (0<<UPM10) | /* parity: none(00), even(01), odd(11) */ \
(0<<UCSZ12) | (1<<UCSZ11) | (1<<UCSZ10); /* data-8bit(011) */ \
sei(); \
} while(0)
#else
# error "USART configuration is needed."
#endif
// I'm fairly sure these aren't needed, but oh well - Jack
/*
* PS/2 Interrupt configuration
*/
#ifdef PS2_USE_INT
/* uses INT1 for clock line(ATMega32U4) */
#define PS2_CLOCK_PORT PORTD
#define PS2_CLOCK_PIN PIND
#define PS2_CLOCK_DDR DDRD
#define PS2_CLOCK_BIT 1
#define PS2_DATA_PORT PORTD
#define PS2_DATA_PIN PIND
#define PS2_DATA_DDR DDRD
#define PS2_DATA_BIT 0
#define PS2_INT_INIT() do { \
EICRA |= ((1<<ISC11) | \
(0<<ISC10)); \
} while (0)
#define PS2_INT_ON() do { \
EIMSK |= (1<<INT1); \
} while (0)
#define PS2_INT_OFF() do { \
EIMSK &= ~(1<<INT1); \
} while (0)
#define PS2_INT_VECT INT1_vect
#endif
/*
* PS/2 Busywait configuration
*/
#ifdef PS2_USE_BUSYWAIT
#define PS2_CLOCK_PORT PORTD
#define PS2_CLOCK_PIN PIND
#define PS2_CLOCK_DDR DDRD
#define PS2_CLOCK_BIT 1
#define PS2_DATA_PORT PORTD
#define PS2_DATA_PIN PIND
#define PS2_DATA_DDR DDRD
#define PS2_DATA_BIT 0
#endif
#endif
#endif