Add support for the KC60 v2.0 2015-09-12 (#360)

* Don't save the ctags file in the repo.

* Initial support for the KC60 board. Only 5x5 working so far.

* Rename because this isn't the same KC60 as others.

* Add in some generic layout.
Pins seem to be in the right order except the 6th column spews
gibberish.

* Don't need this for now.

* Move this to some other folder.

* Trying again to start over.

* Don't need to start over because I figured out why the 'broken' stuff wasn't working.

* Attempt to enable backlighting. It's on on pin B7 like other boards.

* Fix last port changes and fix LED control in keymap.

* Trying some other LED code.

* Bootloader needs to be bigger. Disabling backlight for now.

* Simplify LED code while I try to figure it out.

* Turn back on backlighting.

* Backlighting works now. Just need to get levels or breathing working.

* Trying to allow for turning off the LEDs before I get to brightness levels.

* The missing link: need to run the init_ports function for LEDs to work properly.

* Removing breathing stuff since it bricks the board.

* Clean up default layer.

* Cleanup keymap, KC60 doesn't support a 5th right bottom-row button.
This commit is contained in:
Samuel Goodwin 2016-05-29 19:18:01 +02:00 committed by Jack Humbert
parent b85dd60397
commit 478a18d237
7 changed files with 515 additions and 0 deletions

158
keyboard/kc60_v2/Makefile Normal file
View File

@ -0,0 +1,158 @@
#----------------------------------------------------------------------------
# On command line:
#
# make all = Make software.
#
# make clean = Clean out built project files.
#
# make coff = Convert ELF to AVR COFF.
#
# make extcoff = Convert ELF to AVR Extended COFF.
#
# make program = Download the hex file to the device.
# Please customize your programmer settings(PROGRAM_CMD)
#
# make teensy = Download the hex file to the device, using teensy_loader_cli.
# (must have teensy_loader_cli installed).
#
# make dfu = Download the hex file to the device, using dfu-programmer (must
# have dfu-programmer installed).
#
# make flip = Download the hex file to the device, using Atmel FLIP (must
# have Atmel FLIP installed).
#
# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
# (must have dfu-programmer installed).
#
# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
# (must have Atmel FLIP installed).
#
# make debug = Start either simulavr or avarice as specified for debugging,
# with avr-gdb or avr-insight as the front end for debugging.
#
# make filename.s = Just compile filename.c into the assembler code only.
#
# make filename.i = Create a preprocessed source file for use in submitting
# bug reports to the GCC project.
#
# To rebuild project do "make clean" then "make all".
#----------------------------------------------------------------------------
# Target file name (without extension).
TARGET = kc60
# Directory common source filess exist
TOP_DIR = ../..
TMK_DIR = ../../tmk_core
# Directory keyboard dependent files exist
TARGET_DIR = .
# # project specific files
SRC = kc60.c
ifdef KEYMAP
SRC := keymaps/$(KEYMAP).c $(SRC)
else
SRC := keymaps/default.c $(SRC)
endif
CONFIG_H = config.h
# MCU name
#MCU = at90usb1287
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options
# change yes to no to disable
#
BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
CONSOLE_ENABLE = yes # Console for debug(+400)
COMMAND_ENABLE = yes # Commands for debug and configuration
KEYBOARD_LOCK_ENABLE = yes # Allow locking of keyboard via magic key
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
NKRO_ENABLE = no # USB Nkey Rollover
BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
MIDI_ENABLE = no # MIDI controls
UNICODE_ENABLE = no # Unicode
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE = no # Audio output on port C6
ifdef KEYMAP
ifeq ("$(wildcard keymaps/$(KEYMAP).c)","")
ifneq ("$(wildcard keymaps/$(KEYMAP)/makefile.mk)","")
include keymaps/$(KEYMAP)/makefile.mk
endif
endif
else
ifneq ("$(wildcard keymaps/default/makefile.mk)","")
include keymaps/default/makefile.mk
endif
endif
# Optimize size but this may cause error "relocation truncated to fit"
#EXTRALDFLAGS = -Wl,--relax
# Search Path
VPATH += $(TARGET_DIR)
VPATH += $(TOP_DIR)
VPATH += $(TMK_DIR)
include $(TOP_DIR)/quantum/quantum.mk

View File

@ -0,0 +1,24 @@
kc60 keyboard firmware
======================
## Quantum MK Firmware
For the full Quantum feature list, see [the parent README.md](/README.md).
## Building
Download or clone the whole firmware and navigate to the keyboard/kc60 folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file.
Depending on which keymap you would like to use, you will have to compile slightly differently.
### Default
To build with the default keymap, simply run `make`.
### Other Keymaps
Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `<name>.c` in the keymaps folder, and see keymap document (you can find in top README.md) and existent keymap files.
To build the firmware binary hex file with a keymap just do `make` with `KEYMAP` option like:
```
$ make KEYMAP=[default|jack|<name>]
```
Keymaps follow the format **__\<name\>.c__** and are stored in the `keymaps` folder.

161
keyboard/kc60_v2/config.h Normal file
View File

@ -0,0 +1,161 @@
/*
Copyright 2012 Jun Wako <wakojun@gmail.com>
This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 2 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#ifndef CONFIG_H
#define CONFIG_H
#include "config_common.h"
/* USB Device descriptor parameter */
#define VENDOR_ID 0xFEED
#define PRODUCT_ID 0x6060
#define DEVICE_VER 0x0001
#define MANUFACTURER You
#define PRODUCT kc60v2
#define DESCRIPTION A custom keyboard
/* key matrix size */
#define MATRIX_ROWS 5
#define MATRIX_COLS 14
/*
* Keyboard Matrix Assignments
*
* Change this to how you wired your keyboard
* COLS: AVR pins used for columns, left to right
* ROWS: AVR pins used for rows, top to bottom
* DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
* ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
*
*/
// Possible pins for columns include: F1 F0 E6 D7 D6 D4 C7 C6 B7 B5 B4 B3 B1 B0
// Pins for rows include: D0 D1 F6 F7 D5
#define MATRIX_ROW_PINS { D0, D1, F6, F7, D5 }
#define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B7, D4, B1, B0, B5, B4, D7, D6, B3 }
#define UNUSED_PINS
/* COL2ROW or ROW2COL */
#define DIODE_DIRECTION COL2ROW
/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
#define DEBOUNCING_DELAY 5
/* define if matrix has ghost (lacks anti-ghosting diodes) */
//#define MATRIX_HAS_GHOST
/* number of backlight levels */
#define BACKLIGHT_LEVELS 3
/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
#define LOCKING_SUPPORT_ENABLE
/* Locking resynchronize hack */
#define LOCKING_RESYNC_ENABLE
/*
* Force NKRO
*
* Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
* state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
* makefile for this to work.)
*
* If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
* until the next keyboard reset.
*
* NKRO may prevent your keystrokes from being detected in the BIOS, but it is
* fully operational during normal computer usage.
*
* For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
* or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
* bootmagic, NKRO mode will always be enabled until it is toggled again during a
* power-up.
*
*/
//#define FORCE_NKRO
/*
* Magic Key Options
*
* Magic keys are hotkey commands that allow control over firmware functions of
* the keyboard. They are best used in combination with the HID Listen program,
* found here: https://www.pjrc.com/teensy/hid_listen.html
*
* The options below allow the magic key functionality to be changed. This is
* useful if your keyboard/keypad is missing keys and you want magic key support.
*
*/
/* key combination for magic key command */
#define IS_COMMAND() ( \
keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
)
/* control how magic key switches layers */
//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true
//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true
//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
/* override magic key keymap */
//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
//#define MAGIC_KEY_HELP1 H
//#define MAGIC_KEY_HELP2 SLASH
//#define MAGIC_KEY_DEBUG D
//#define MAGIC_KEY_DEBUG_MATRIX X
//#define MAGIC_KEY_DEBUG_KBD K
//#define MAGIC_KEY_DEBUG_MOUSE M
//#define MAGIC_KEY_VERSION V
//#define MAGIC_KEY_STATUS S
//#define MAGIC_KEY_CONSOLE C
//#define MAGIC_KEY_LAYER0_ALT1 ESC
//#define MAGIC_KEY_LAYER0_ALT2 GRAVE
//#define MAGIC_KEY_LAYER0 0
//#define MAGIC_KEY_LAYER1 1
//#define MAGIC_KEY_LAYER2 2
//#define MAGIC_KEY_LAYER3 3
//#define MAGIC_KEY_LAYER4 4
//#define MAGIC_KEY_LAYER5 5
//#define MAGIC_KEY_LAYER6 6
//#define MAGIC_KEY_LAYER7 7
//#define MAGIC_KEY_LAYER8 8
//#define MAGIC_KEY_LAYER9 9
//#define MAGIC_KEY_BOOTLOADER PAUSE
//#define MAGIC_KEY_LOCK CAPS
//#define MAGIC_KEY_EEPROM E
//#define MAGIC_KEY_NKRO N
//#define MAGIC_KEY_SLEEP_LED Z
/*
* Feature disable options
* These options are also useful to firmware size reduction.
*/
/* disable debug print */
//#define NO_DEBUG
/* disable print */
//#define NO_PRINT
/* disable action features */
//#define NO_ACTION_LAYER
//#define NO_ACTION_TAPPING
//#define NO_ACTION_ONESHOT
//#define NO_ACTION_MACRO
//#define NO_ACTION_FUNCTION
#endif

111
keyboard/kc60_v2/kc60.c Normal file
View File

@ -0,0 +1,111 @@
#include "kc60.h"
__attribute__ ((weak))
void matrix_init_user(void) {
// leave this function blank - it can be defined in a keymap file
};
__attribute__ ((weak))
void matrix_scan_user(void) {
// leave this function blank - it can be defined in a keymap file
}
__attribute__ ((weak))
bool process_action_user(keyrecord_t *record) {
// leave this function blank - it can be defined in a keymap file
return true;
}
__attribute__ ((weak))
void led_set_user(uint8_t usb_led) {
// leave this function blank - it can be defined in a keymap file
}
void matrix_init_kb(void) {
// put your keyboard start-up code here
// runs once when the firmware starts up
#ifdef BACKLIGHT_ENABLE
backlight_init_ports();
#endif
matrix_init_user();
}
void matrix_scan_kb(void) {
// put your looping keyboard code here
// runs every cycle (a lot)
matrix_scan_user();
}
bool process_action_kb(keyrecord_t *record) {
// put your per-action keyboard code here
// runs for every action, just before processing by the firmware
return process_action_user(record);
}
void led_set_kb(uint8_t usb_led) {
// put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
led_set_user(usb_led);
}
#ifdef BACKLIGHT_ENABLE
#define CHANNEL OCR1B
void backlight_init_ports()
{
// Setup PB6 as output and output low.
DDRB |= (1<<6);
PORTB &= ~(1<<6);
// Use full 16-bit resolution.
ICR1 = 0xFFFF;
// I could write a wall of text here to explain... but TL;DW
// Go read the ATmega32u4 datasheet.
// And this: http://blog.saikoled.com/post/43165849837/secret-konami-cheat-code-to-high-resolution-pwm-on
// Pin PB7 = OCR1C (Timer 1, Channel C)
// Compare Output Mode = Clear on compare match, Channel C = COM1B1=1 COM1C0=0
// (i.e. start high, go low when counter matches.)
// WGM Mode 14 (Fast PWM) = WGM13=1 WGM12=1 WGM11=1 WGM10=0
// Clock Select = clk/1 (no prescaling) = CS12=0 CS11=0 CS10=1
TCCR1A = _BV(COM1B1) | _BV(WGM11); // = 0b00001010;
TCCR1B = _BV(WGM13) | _BV(WGM12) | _BV(CS10); // = 0b00011001;
backlight_init();
}
void backlight_set(uint8_t level)
{
// Prevent backlight blink on lowest level
PORTB &= ~(_BV(PORTB6));
if ( level == 0 )
{
// Turn off PWM control on PB6, revert to output low.
TCCR1A &= ~(_BV(COM1B1));
CHANNEL = 0x0;
}
else if ( level == BACKLIGHT_LEVELS)
{
// Turn on PWM control of PB6
TCCR1A |= _BV(COM1B1);
// Set the brightness
CHANNEL = 0xFFFF;
}
else
{
// Turn on PWM control of PB6
TCCR1A |= _BV(COM1B1);
// Set the brightness
CHANNEL = 0xFFFF >> ((BACKLIGHT_LEVELS - level) * ((BACKLIGHT_LEVELS + 1) / 2));
}
}
#endif

36
keyboard/kc60_v2/kc60.h Normal file
View File

@ -0,0 +1,36 @@
#ifndef KC60_H
#define KC60_H
#include "matrix.h"
#include "keymap_common.h"
#ifdef BACKLIGHT_ENABLE
#include "backlight.h"
#endif
#include <avr/io.h>
#include <stddef.h>
// This a shortcut to help you visually see your layout.
// The first section contains all of the arguements
// The second converts the arguments into a multi-dimensional array
#define KEYMAP( \
K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, \
K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \
K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2C, K2D, \
K30, K31, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K3D, \
K40, K41, K42, K45, K4A, K4B, K4C, K4D \
) { \
{ K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D }, \
{ K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D }, \
{ K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2C, K2D }, \
{ K30, K31, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K3D }, \
{ K40, K41, K42, KC_NO, KC_NO, K45, KC_NO, KC_NO, KC_NO, KC_NO,K4A, K4B, K4C, K4D } \
}
void matrix_init_user(void);
void matrix_scan_user(void);
bool process_action_user(keyrecord_t *record);
void led_set_user(uint8_t usb_led);
void backlight_init_ports(void);
#endif

View File

@ -0,0 +1,24 @@
// This is the canonical layout file for the Quantum project. If you want to add another keyboard,
// this is the style you want to emulate.
#include "kc60.h"
const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
[0] = KEYMAP( /* Basic QWERTY */
KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, \
KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, \
KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_NO, KC_ENT, \
KC_LSFT, KC_NO, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_NO, KC_RSFT, \
KC_LCTL, KC_LALT, KC_LGUI, KC_SPC, KC_RGUI, KC_RALT, KC_RCTL, RESET \
),
};
const uint16_t PROGMEM fn_actions[] = {
};
const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
{
// MACRODOWN only works in this function
return MACRO_NONE;
};

1
keyboard/planck/.gitignore vendored Normal file
View File

@ -0,0 +1 @@
tags