qmk_firmware/lib/lufa/Bootloaders/MassStorage/makefile

76 lines
3.3 KiB
Makefile

#
# LUFA Library
# Copyright (C) Dean Camera, 2017.
#
# dean [at] fourwalledcubicle [dot] com
# www.lufa-lib.org
#
# --------------------------------------
# LUFA Project Makefile.
# --------------------------------------
# Run "make help" for target help.
MCU = at90usb1287
ARCH = AVR8
BOARD = USBKEY
F_CPU = 8000000
F_USB = $(F_CPU)
OPTIMIZATION = s
TARGET = BootloaderMassStorage
SRC = $(TARGET).c Descriptors.c BootloaderAPI.c BootloaderAPITable.S Lib/SCSI.c Lib/VirtualFAT.c $(LUFA_SRC_USB) $(LUFA_SRC_USBCLASS)
LUFA_PATH = ../../LUFA
CC_FLAGS = -DUSE_LUFA_CONFIG_HEADER -IConfig/ -DBOOT_START_ADDR=$(BOOT_START_OFFSET)
LD_FLAGS = -Wl,--section-start=.text=$(BOOT_START_OFFSET) $(BOOT_API_LD_FLAGS)
# Flash size and bootloader section sizes of the target, in KB. These must
# match the target's total FLASH size and the bootloader size set in the
# device's fuses.
FLASH_SIZE_KB = 128
BOOT_SECTION_SIZE_KB = 8
# Bootloader address calculation formulas
# Do not modify these macros, but rather modify the dependent values above.
CALC_ADDRESS_IN_HEX = $(shell printf "0x%X" $$(( $(1) )) )
BOOT_START_OFFSET = $(call CALC_ADDRESS_IN_HEX, ($(FLASH_SIZE_KB) - $(BOOT_SECTION_SIZE_KB)) * 1024 )
BOOT_SEC_OFFSET = $(call CALC_ADDRESS_IN_HEX, ($(FLASH_SIZE_KB) * 1024) - ($(strip $(1))) )
# Bootloader linker section flags for relocating the API table sections to
# known FLASH addresses - these should not normally be user-edited.
BOOT_SECTION_LD_FLAG = -Wl,--section-start=$(strip $(1))=$(call BOOT_SEC_OFFSET, $(3)) -Wl,--undefined=$(strip $(2))
BOOT_API_LD_FLAGS = $(call BOOT_SECTION_LD_FLAG, .apitable_trampolines, BootloaderAPI_Trampolines, 96)
BOOT_API_LD_FLAGS += $(call BOOT_SECTION_LD_FLAG, .apitable_jumptable, BootloaderAPI_JumpTable, 32)
BOOT_API_LD_FLAGS += $(call BOOT_SECTION_LD_FLAG, .apitable_signatures, BootloaderAPI_Signatures, 8)
# Check if the bootloader needs an AUX section, located before the real bootloader section to store some of the
# bootloader code. This is required for 32KB and smaller devices, where the actual bootloader is 6KB but the maximum
# bootloader section size is 4KB. The actual usable application space will be reduced by 6KB for these devices.
ifeq ($(BOOT_SECTION_SIZE_KB),8)
CC_FLAGS += -DAUX_BOOT_SECTION_SIZE=0
else
AUX_BOOT_SECTION_SIZE_KB = (6 - $(BOOT_SECTION_SIZE_KB))
CC_FLAGS += -DAUX_BOOT_SECTION_SIZE='($(AUX_BOOT_SECTION_SIZE_KB) * 1024)'
LD_FLAGS += -Wl,--section-start=.boot_aux=$(call BOOT_SEC_OFFSET, (($(BOOT_SECTION_SIZE_KB) + $(AUX_BOOT_SECTION_SIZE_KB)) * 1024 - 16))
LD_FLAGS += $(call BOOT_SECTION_LD_FLAG, .boot_aux_trampoline, Boot_AUX_Trampoline, ($(BOOT_SECTION_SIZE_KB) + $(AUX_BOOT_SECTION_SIZE_KB)) * 1024)
endif
# Default target
all:
# Include LUFA-specific DMBS extension modules
DMBS_LUFA_PATH ?= $(LUFA_PATH)/Build/LUFA
include $(DMBS_LUFA_PATH)/lufa-sources.mk
include $(DMBS_LUFA_PATH)/lufa-gcc.mk
# Include common DMBS build system modules
DMBS_PATH ?= $(LUFA_PATH)/Build/DMBS/DMBS
include $(DMBS_PATH)/core.mk
include $(DMBS_PATH)/cppcheck.mk
include $(DMBS_PATH)/doxygen.mk
include $(DMBS_PATH)/dfu.mk
include $(DMBS_PATH)/gcc.mk
include $(DMBS_PATH)/hid.mk
include $(DMBS_PATH)/avrdude.mk
include $(DMBS_PATH)/atprogram.mk