qmk_firmware/keyboards/ergodone/rules.mk
Jack Humbert d2ff66a985 Creates a layouts/ folder for keymaps shared between keyboards (#1609)
* include variables and .h files as pp directives

* start layout compilation

* split ergodoxes up

* don't compile all layouts for everything

* might seg fault

* reset layouts variable

* actually reset layouts

* include rules.mk instead

* remove includes from rules.mk

* update variable setting

* load visualizer from path

* adds some more examples

* adds more layouts

* more boards added

* more boards added

* adds documentation for layouts

* use lowercase names for LAYOUT_

* add layout.json files for each layout

* add community folder, default keymaps for layouts

* touch-up default layouts

* touch-up layouts, some keyboard rules.mk

* update documentation for layouts

* fix up serial/i2c switches
2017-08-23 22:29:07 -04:00

95 lines
3.7 KiB
Makefile

#----------------------------------------------------------------------------
# On command line:
#
# make = Make software.
#
# make clean = Clean out built project files.
#
# That's pretty much all you need. To compile, always go make clean,
# followed by make.
#
# For advanced users only:
# make teensy = Download the hex file to the device, using teensy_loader_cli.
# (must have teensy_loader_cli installed).
#
#----------------------------------------------------------------------------
# # project specific files
SRC = \
twimaster.c \
matrix.c \
expander.c \
# MCU name
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options
# comment out to disable the options.
#
CUSTOM_MATRIX = yes # Custom matrix file for the ErgoDone
UNICODE_ENABLE = yes # Unicode
BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
CONSOLE_ENABLE = no # Console for debug(+400)
COMMAND_ENABLE = no # Commands for debug and configuration
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
USB_6KRO_ENABLE = no # USB 6key Rollover
BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality
KEYMAP_IN_EEPROM_ENABLE = no # External keymap in eeprom
KEYMAP_SECTION_ENABLE = no # Fixed address keymap for keymap editor
SOFTPWM_LED_ENABLE = no # Enable SoftPWM to drive backlight
FADING_LED_ENABLE = no # Enable fading backlight
BREATHING_LED_ENABLE = no # Enable breathing backlight
LEDMAP_ENABLE = no # Enable LED mapping
LEDMAP_IN_EEPROM_ENABLE = no # Read LED mapping from eeprom
ONEHAND_ENABLE = no # Disable Onehand
RGBLIGHT_ENABLE = no
MIDI_ENABLE = no
LAYOUTS = ergodox ergodox_80